Tabla De Contenido - Bosch 5312 Instrucciones De Funcionamiento Y Seguridad

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

_
READ ALL INSTRUCTIONS" -- Failure to follow the SAFETY RULES identified by
BULLET (,) symbol listed BELOW and other safety precautions, may result in serious
personal injury.
Double insulated Tools
Double insulation []
is a design concept used in
electric power tools which eliminates the need for
the three wire grounded power cord and grounded
power supply system.
It is a recognized and ap-
proved system by Underwriter's Laboratories, CSA
and Federal OSHA authorities.
• Servicing of a tool with double insulation requires
care and knowledge of the system and should be
performed only by a qualified service technician.
• WHEN SERVICING, USE ONLY IDENTICAL RE-
PLACEMENT PARTS.
• POLARIZED PLUGS. To reduce the risk of elec-
trical shock, your tool is equipped with a polarized
plug (one blade is wider than the other), this plug
will fit in a polarized outlet only one way. Ifthe plug
does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician to in-
stall the proper outlet. To reduce the risk of elec-
trical shock, do not change the plug in any way.
Extension Cords
• Replace damaged cords immediately.
Use of
damaged cords can shock, burn or electrocute.
• Ifan extension cord is necessary, a cord with ade-
quate size conductors should be used to prevent
excessive voltage drop, loss of power or overheat-
ing. The table shows the correct size to use, de-
pending on cord length and nameplate amperage
rating of tool. If in doubt, use the next heavier
gauge. Always use U.L. and CSA listed extension
cords.
RECOMMENDED SIZES
Tool's
Cord
Size
in A.W.G,
Ampere
Cord
LerBgth
in Feet
Rating
25
50
188
150
3-6
18
16
16
14
6-8
18
16
14
12
8-10
18
16
14
12
10-12
16
16
14
12
12-16
14
12
)F EXTENSION
Wire Sizes
in mm 2
Cord
Length
in Meters
15
30
60
120
0.75 0.75 1.5
2.5
0.75 1.0 2.5
4.0
0.75 1.0 2.5
4.0
1.0 2.5
4.0
--
NOTE: The smaller the gauge number, the heavier
the cord.
"SAVE THESE INSTRUCTIONS"
Safety ..............................
2-6
General Safety Rules For Bench Top Tools .2
Safety Rules For Miter Saws ............
3-6
Table of Contents
....................
6
Electrical Requirements ...............
7
Getting To Know Your Miter Saw
.......
7-9
...........................
10-12
Tools Needed for Assembly and Alignment .10
Unpacking and Checking Contents .......
10
11-12
12
Adjustments
.........................
13-16
13
13
Blade 45° To The Table .................
14
Blade Square To Fence .................
15
15
Kerr Insert ...........................
16
Depth Adjustment .....................
16
Transporting,
Placement and Mounting .17-18
Mounting Applications ..................
17
Mounting the saw ....................
18
Adjusting
the Four Position Switch
18
...............
19-22
Body and Hand Position
..............
19
...................
20-21
Switch Activation
....................
21
.....................
22
..........
22
....................
23-30
..........................
23
..........................
23
..........................
24
Bevel Cut ..........................
25
.....................
26
....................
27
.................
28
................
28-30
Special Cuts ........................
31-33
.........
34-35
Belt Changes
......................
34
....................
35-36
Accessories
.......................
37
-6-

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

5412

Tabla de contenido