Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
2. Installation location
®T
©
®
2.1. Outline dimensions (indoor unit) (Fig. 2-1)
Select a proper position allowing the following clearances for installation and mainte-
nance.
(mm)
(inch)
Models
W
B
H
(_)
_
_F_
_G_
(_
990
235
340
Mn 30
Max 130 Mn 180
Mn 50
Mn 160
A12, A18
39
9-1/4
13-3/8
Min. l -13/16 Max. 5
Max.7-3/32Min. l -31/32Min.5-29/32
_ Ceiling
© Wall
@ Furnishing, etc
Warning:
Mount the indoor unit on a ceiling
strong
enough to withstand
the weight
of the
unit.
2.2. Outline dimensions
(Outdoor
unit)
Refer to the outdoor unit installation
manual.
Fig. 2-1
3. Installing
the indoor
unit
@
®
®
®
®
®
®
®
Fig. 3-1
3.1. Check the indoor unit accessories
(Fig. 3-1)
The indoor unit should be supplied with the following accessories.
PARTNUMBER
d_
®
®
®
®
®
®
®
®
®
ACCESSORY
Mount board
Tapping screw 4 × 35
Pipe cover
Band
Felt tape
Wireless remote controller
Remocon
holder
Alkali batteries (size AAA)
Mount piece (Package)
Wired remote controller
Drain adaptor
QUANTITY
1
12
1
5
3
1
1
2
1
1
1
LOCATION OFSETTING
Fixatthe backofthe unit
Set inside the unit
for PKA-A,GAL
for PKA-A,GA
(_) - ® are stored
in a cut-out
section
of the packing material
(styrofoam).
(inch)
©
3.2. installing the wall mounting
fixture (Fig. 3-2)
3.2.1.
Setting
the wall
mounting
fixture
and
piping
positions
Using the wall mounting
fixture,
determine
the unit's
installation
position
and the locations of the piping holes to be drilled.
z_ Warning:
Before
drilling
a hole in the wall, you must consult
the building contractor.
Supporting
piece
_ Mount board
© Main body
@ Slot (6-11 x 20,
8P-7/16 x 25/32 inch)
Unit center
CF}Bolt hole (14-o14
ram,
14P-9/16
inch)
_) Tapping hole (49-o5
ram,
49P-3/16
inch)
CH}Bottom left pipe slot
(o90 mm, 3-9/18 inch)
Bottom left pipe slot knockout
hole
(_) Bottom right pipe slot (o90 ram, 3-9/16 inch)
Bottom right pipe slot knockout hole
_L_ Liquid pipe flare connection
position
@ Gas pipe flare connection
position
(_) Level setting
standard
_) Insert scale.
Hole centre
(_) Align the scale with the line.
©
@
®®
Fig. 3-2
®
Fig. 3-3
Sleeve
_
Hole
©
(Indoors)
@ Wall
_} (Outdoors)
3.2.2.
Drilling
the
piping
hole
(Fig.
3-3)
Use a core drill to make a hole of 90-100 ram, 3-9/16 to 4 inch diameter in the
wail in the piping direction,
at the position shown
in the diagram
to the left.
The hole should
incline so that the outside
opening
is lower than the inside
opening.
I_ Insert a sleeve
(with a 90 ram, 3-9/16 inch diameter
and purchased
locally)
through
the hole.
Note:
The purpose
of the hole's
inclination
is to promote drain flow.
3
Publicidad
Capítulos
Tabla de contenido
