Product Specifications; Emissions Information; High Altitude Operation - Generac OneWASH Power Washer Manual Del Operador

3.1.1 — ITEMS NOT SHOWN
Identification Label (on engine blower housing) –
Provides model and serial number of power washer.
Please have these readily available if calling for assis-
tance.
Detergent Siphoning Tube/Filter – Use to siphon power
washer safe detergents into the low pressure stream.
3.2 — P S
RODUCT
Pressure - (PSI / BAR) .............................. 3100/213 Max
Flow Rate - (GPM / LPM) ............................ 2.8/10.6 Max
Water supply temperature - (°F / C°) ............. 100/38 Max
Hose length - (Feet / Meters).................................. 30/9.1
Chemical Tank(s) - Number per unit............................... 1
Chemical Tank - Capacity (Gal) N/A.......................... 0.75
Nozzles - Number per unit.............................................. 3
Lance Length (Inches / cm) ..................................... 20/51
Gun.....................................................................Standard
Engine Displacement - (Cubic Inch / cc) ............ 12.9/212
Spark Plug Type .................................F7TC or equivalent
Spark Plug Gap - (Inches / mm) ....0.028-0.031/0.70-0.80
Fuel Capacity - (Quarts / Liters) ............................ 3.7/3.5
Oil Capacity - (Oz / Liters) ...................................... 20/0.6
On/Off Switch ............................................................. Yes
3.3 — E
MISSIONS
The U.S. Environmental Protection Agency (and Califor-
nia Air Resource Board for equipment certified to CA
standards) requires that this engine comply with exhaust
and evaporative emission standards. Locate the emis-
sions compliance decal on the engine to determine what
standards the engine meets, and to determine which
emissions warranty applies. The engine is certified to
meet the applicable emission standards on gasoline. It is
important to follow the maintenance specifications in the
Maintenance section to ensure that the engine complies
with the applicable emission standards for the duration of
the product's life. This engine utilizes lean carburetion
settings and other systems to reduce emissions. Tamper-
ing with or altering the emission control system may
increase emissions and may be a violation of Federal or
California Law. Acts that constitute tampering include but
are not limited to:
• Removal or alteration of any part of the intake, fuel, or
exhaust systems
• Altering or defeating the governor linkage or speed-
adjusting mechanism to cause the engine to operate
outside its design parameters
If you are aware of any of the following symptoms, have
your engine inspected and repaired by your servicing
dealer:
8
PECIFICATIONS
I
NFORMATION
• Hard starting or stalling after starting
• Rough idle
• Misfiring or backfiring under load
• Afterburning (backfiring)
• Black exhaust smoke or high fuel consumption
3.4 — H A
IGH LTITUDE
The fuel system on this engine may be influenced by
operation at higher altitudes. Proper operation can be
ensured by installing an altitude kit when required. See
the table below to determine when an altitude kit is
required. Operating this engine without the proper alti-
tude kit installed may increase the engine's emissions
and decrease fuel economy and performance. Kits may
be obtained from any Dealer and should be installed by a
qualified individual.
Altitude* Kit Number
0 - 5000 Feet Not Required
5000 - 7000 Feet
* Elevation above sea level.
If the altitude kit has been installed and the engine
will be operated at an altitude where the kit is not
required, the engine should be returned to the origi-
nal factory configuration. Operating the engine at
lower altitudes with the kit installed may cause the
engine to overheat and result in serious engine dam-
age, and may result in decreased performance and
increased emissions.
General Information
O
PERATION
PSI
3100
0K2016 3100
NOTE:
OneWASH™ Power Washer