Product Specifications; Emissions Information; High Altitude Operation; Unpacking - Generac OneWASH Power Washer Manual Del Operador

PROduCT SPeCIfICATIONS

Pressure - (PSI / BAR) ..................... 3000/207 & 3100/213 Max
Flow Rate - (GPM / LPM) .......................................2.8/10.6 Max
Water supply temperature - (°F / C°) ........................100/38 Max
Hose length - (Feet / Meters) ........................................... 30/9.1
Chemical Tank(s) - Number per unit ......................................... 1
Chemical Tank - Capacity (Gal) N/A .................................... 0.75
Nozzles - Number per unit ........................................................ 3
Lance Length (Inches / cm) .............................................. 20/51
Gun ..............................................................................Standard
Engine Displacement - (Cubic Inch / cc) ...................... 12.9/212
Spark Plug Type .............................................F7TC or equivalent
Spark Plug Gap - (Inches / mm) ............ 0.028-0.031/0.70-0.80
Fuel Capacity - (Quarts / Liters) ...................................... 3.7/3.5
Oil Capacity - (Oz / Liters) ................................................ 20/0.6
Low Oil Shut Down System ..................................................Yes
Low Water Sensor Shut Down System ..................................Yes
On/Off Switch .......................................................................Yes

eMISSIONS INfORMATION

The U.S. Environmental Protection Agency (and California Air
Resource Board for equipment certified to CA standards) requires
that this engine comply with exhaust and evaporative emission
standards. Locate the emissions compliance decal on the engine
to determine what standards the engine meets, and to determine
which emissions warranty applies. The engine is certified to meet
the applicable emission standards on gasoline. It is important to
follow the maintenance specifications in the Maintenance section
to ensure that the engine complies with the applicable emission
standards for the duration of the product's life. This engine utilizes
lean carburetion settings and other systems to reduce emissions.
Tampering with or altering the emission control system may
increase emissions and may be a violation of Federal or California
Law. Acts that constitute tampering include but are not limited to:
• Removal or alteration of any part of the intake, fuel, or exhaust
systems
• Altering or defeating the governor linkage or speed-adjusting
mechanism to cause the engine to operate outside its design
parameters
If you are aware of any of the following symptoms, have your
engine inspected and repaired by your servicing dealer:
• Hard starting or stalling after starting
• Rough idle
• Misfiring or backfiring under load
• Afterburning (backfiring)
• Black exhaust smoke or high fuel consumption

HIGH AlTITude OPeRATION

The fuel system on this engine may be influenced by operation at
higher altitudes. Proper operation can be ensured by installing an
altitude kit when required. See the table below to determine when
an altitude kit is required. Operating this engine without the proper
altitude kit installed may increase the engine's emissions and
decrease fuel economy and performance. Kits may be obtained
from any Dealer and should be installed by a qualified individual.
Altitude* kit Number
0 - 5000 Feet Not Required
5000 - 7000 Feet
*Elevation above sea level.
If the altitude kit has been installed and the engine will be
operated at an altitude where the kit is not required, the
engine should be returned to the original factory configuration.
Operating the engine at lower altitudes with the kit installed
may cause the engine to overheat and result in serious engine
damage, and may result in decreased performance and
increased emissions.

uNPACkING

1. Remove the parts bag, accessories, and inserts included with
power washer.
2. Open carton completely by cutting each corner from top to
bottom.
3. Ensure you have all included items prior to assembly.
• Main Unit
• Handle Assembly
• High Pressure Hose
• Siphon Hose & Filter
• Spray Gun
• Lance with Quick Connect Fitting
• Oil Bottle
• Hose Hook Wire form
• Parts Bag (which includes the following):
– Operator's Manual
– Warranty Statement
– Emission Warranty Statement
– CARB Emission Warranty Statement
– Owner's Registration Card
– Bag containing Color-coded Nozzles
– 4mm Allen wrench
– Screw (Qty 4)
– Tree clips (Qty 4)
– Plastic Gun Holder
– Plastic Lance Holder
4. If you are missing any items from your carton, please call
Generac Customer Service at 1-888-436-3722. When calling
for assistance, please have the model and serial number from
the data tag available.
5. Fill out and send in registration card. Write Model number,
Serial number & date of purchase in the table located in the
"Where to Find Us" section.
General Information
PSI
3000/3100
0K2016 3000/3100
NOTe:
5