Tabla De Contenido - Ingersoll Rand HD Serie Manual Del Usuario

PART NUMBER FOR ORDERING
Common parts for ALL HD,
HX and HXD Grinders
1 Inlet Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . LG2-A465
2 Inlet Screen . . . . . . . . . . . . . . . . . . . . . . . . . . R1602-61
•
3 Inlet Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . R18LF-21
4 Throttle Valve Spring Seat . . . . . . . . . . . . . . . . . . LG3-592
5 Throttle Valve Spring . . . . . . . . . . . . . . . . . . . . . . 7L-51
6 Throttle Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . LG3-302
•
7 Throttle Valve Seat . . . . . . . . . . . . . . . . . . . . . . . LG3-303
8 Motor Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . LG3-40
9 Throttle Lever . . . . . . . . . . . . . . . . . . . . . . . . . . . LG2-273
9A Locking Throttle Lever Assembly
(for all models ending in L or C) . . . . . . . . . . . . . LG2-A400
* Lever Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . LG1-402
* Lock Spring . . . . . . . . . . . . . . . . . . . . . . . . . . LG1-405
* Lock Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5UT-757
10 Throttle Lever Pin . . . . . . . . . . . . . . . . . . . . . . . . 61H-120
11 Throttle Valve Plunger . . . . . . . . . . . . . . . . . . . . . LG2-191
12 Rear Rotor Bearing . . . . . . . . . . . . . . . . . . . . . . . R120-127
•
13 Rear Rotor Bearing Spacer (2) . . . . . . . . . . . . . . 400-25-191
•
14 Rear Rotor Bearing Retainer . . . . . . . . . . . . . . . . LG1-118
15 Rotor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LG3-53-4
•
16 Vane Packet (set of 4 Vanes) . . . . . . . . . . . . . . . . DG31-42-4
* Not illustrated.
• To keep downtime to a minimum, it is desirable to have on hand certain repair parts. We recommend that you stock one (pair or set) of each part indicated by a
bullet (•) for every four tools in service.
+ Standard equipment with models ending in M, MC or ML and ALL Front Exhaust models; optional equipment on all other models.
# Always install a Locking Throttle Lever Assembly (9A) on a tool with a Low Profile Concentric Flange (22A). Do not equip a tool with a standard
non-lockingLever (9) and low profile concentric Flange. This can allow the tool to continue to run if dropped or set down.
PART NUMBER FOR ORDERING
17 Front End Plate . . . . . . . . . . . . . . . . . . . . . . . . . . LG2-11
18 Front End Plate Spacer . . . . . . . . . . . . . . . . . . . . LG2-65
• 19
Front Seal Cup Assembly . . . . . . . . . . . . . . . . . . 61H-A32
20 Front Rotor Bearing . . . . . . . . . . . . . . . . . . . . . . . LG2-24
21 Flow Ring
for HD120 and HX120
(12 000 rpm) (grey) . . . . . . . . . . . . . . . . . LG2-103-0
for HD150 and HX150
(15 000 rpm) (brown) . . . . . . . . . . . . . . . LG2-103-1
for HD180, HX180 and
HXD180 (18 000 rpm) (blue) . . . . . . . . . LG3-103-3
22 High Profile Flange . . . . . . . . . . . . . . . . . . . . . . . LG2-23
# 22A Concentric Flange . . . . . . . . . . . . . . . . . . . . . . . . LG3R-23
23 Flange Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . LG2-29
+ Exhaust Hose Adapter Kit . . . . . . . . . . . . . . . . . . LG2-K284
+ 24 Exhaust Hose Adapter . . . . . . . . . . . . . . . LG2-184
+ 25 Exhaust Hose . . . . . . . . . . . . . . . . . . . . . . 3RL-284
+ 25A Exhaust Hose Retainer . . . . . . . . . . . . . . . 6WT-203
* Warning Label
for models ending in H63-EU . . . . . . EU-63-99
for models ending in H64-EU . . . . . . EU-64-99
for all other models ending in -EU . . EU-99
for all other models . . . . . . . . . . . . . . LG2-99