Setting The Depth Of Cut - Parkside POF 1300 Instrucciones De Utilización Y De Seguridad

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Operation

Setting the depth of cut

Q
m Danger! Set the cutting depth only after the
device has been switched off!
Coarse setting of the depth of cut
16
1. Ensure that the clamping lever
is released turn it anticlockwise until it is applied.
2. Place the device on the workpiece.
3. Turn the fine adjustment knob
cut until the markings for zero-reset
back of the device are in alignment.
4. Turn the scale for fine adjustment of depth of
cut in mm
until the "0" point aligns with the
13
marking on the housing.
5. Turn the step buffer
lowest position.
6. Release the stop screw
7. Release the clamping lever
clockwise and press the device downwards
until the router bit comes into contact with the
workpiece surface.
8. Apply the clamping lever
clockwise.
9. Push the depth stop
ting at the lowest position of the step buffer
Press the slider with index mark
"0" of the scale for coarse adjustment of depth
of cut in mm
.
12
10. Set the depth stop
depth and tighten the stop screw
stop. After this, the setting of the slider with
index mark
should not be changed.
11
11. Release the clamping lever
the device back up again.
42 GB/MT
14
13
1.0
is applied. If it
15
for depth of
14
on the
16
until it engages in the
7
for depth stop.
9
by turning it
15
by turning it anti-
15
downwards until it is sit-
10
to position
11
to the desired routing
10
for depth
9
and then guide
15
After setting the depth of cut do not change the set-
ting of the slider with index mark
stop
. The current depth of cut setting can now be
10
read on the scale for coarse adjustment of depth of
cut in mm
.
12
Example: Create a guide slot in a pine drawer:
width: 16 mm, depth: 10 mm
j
Select the 16 mm slot cutter from the router bit
set and insert it as described in the section about
"Inserting a router bit".
j
Preselect a medium rotational speed (approx.
3 - 4).
j
Carry out steps 1 to 9 as described in the sec-
tion above.
j
Set the required depth of cut by setting the depth
stop
to "10" on the scale for coarse adjust-
10
ment of depth of cut in mm
the stop screw for depth stop
j
Secure the workpiece and carry out the routing
process as described in the following sections.
Fine setting the depth of cut
The depth of cut can be adjusted using the fine ad-
justment knob
14
0.1 mm / 1 revolution = 1.5 mm) max. + - 8 mm
movement.
Example: Take the device back up and measure
the machined slot depth (required ma-
chined depth = 10 mm / actual = 9.8 mm)
j
Place the device in a position which allows the
router bit to be lowered without obstruction.
j
Release the clamping lever
clockwise and press the device carefully down-
.
wards until the depth stop
7
buffer
.
7
j
Apply the clamping lever
clockwise.
j
Turn the scale for fine adjustment of depth of
cut in mm
13
for depth stop
9
j
Use the fine adjustment knob
depth of cut by 0.2 mm / 2 divisions (= differ-
ence between required and actual), turn clock-
wise, in the direction of the + arrow.
on the depth
11
. Now tighten
12
.
9
for depth of cut. (1 division =
by turning it
15
sits on the step
10
by turning it anti-
15
to "0". Release the stop screw
.
10
to change the
14

Publicidad

Tabla de contenido
loading

Tabla de contenido