California Proposition; General Safety; Important - Campbell Hausfeld HV2100 Instrucciones De Funcionamiento Y Manual De Piezas

Operating Instructions and Parts Manual
General Safety Information

CALIFORNIA PROPOSITION 65

This product or its
power cord may
contain chemicals, including lead, known
to the State of California to cause cancer
and birth defects or other reproductive
harm. Wash hands after handling.

GENERAL SAFETY

Read all instructions and safety
precautions before operating
the unit.
Risk of fire or
explosion! Solvent
and paint fumes
can explode or
ignite, causing
severe injury and property damage.
Do not use to spray HALOGENATED
HYDROCARBONS. Paints and solvents
containing halogenated hydrocarbons
can react explosively with aluminum.
Always check the product's label before
using these materials in the unit.
Unit is not intended for spraying
flammable materials other than lacquer.
See specific directions for spraying with
lacquer on chart 1.
Make sure the room is well-ventilated.
Avoid all ignition sources, such as static
electricity sparks, open flames, hot
objects, sparks from connecting and
disconnecting power cords, and working
light switches.
Follow the material and solvent
manufacturers' safety precautions and
warnings. Do not use liquids with flash
points less than 100˚ F (38˚ C).
Do not carry TURBINE while spraying.
Keep the turbine at maximum distance
from spraying area.
Static electricity can be produced by
HVLP spraying. Make sure any electrically
conductive object being sprayed is
grounded to prevent static sparking. The
sprayer is grounded through the electric
cord. If an extension cord is necessary,
the cord must be a grounded, 115 volt,
three wire type cord.
Hazardous vapors: Paints,
solvents, insecticides, and
other materials may be
harmful if inhaled causing
severe nausea, fainting or
poisoning.
www.campbellhausfeld.com
Air Flow
Ring
Aircap
MANUAL
Retaining
Ring
Figure 2 - Needle / Nozzle Installation
Always wear a mask or
respirator and eye protection
when painting. Be certain
mask or respirator will provide
necessary protection against
inhalation of harmful vapors.
NEVER point spray gun at any part of the
body or at anyone else.
Tipping gun may cause clogs. Dried spray
material also clogs pressure delivery
tube and fittings. The spray gun will not
function when clogged.
When not in use, be sure to disconnect
hose and place gun on a solid, level
surface to avoid tipping.
Components
(1) Gun - fully assembled, with 1.00 mm
"all purpose" needle/nozzle installed
Accessories located in paint cup, or in
storage compartment of turbine:
(1) Viscosity stick
(1) Cleaning brush
(1) Gun wrench
Setup
NEEDLE AND NOZZLE ASSEMBLY
IMPORTANT: The needle and nozzle are
a matched as sem bly. It is very important
that both the needle and nozzle are cor-
rect ly selected and installed. The
nee dle/nozzle kits are identified by a
number inscribed on each component.
Make sure the numbers on the noz zle
and the needle match. Failure to match
these two com po nents will result in poor
finish quality.
Aircap Spring
Nozzle
2
HV2100, HV2105, HV3500
Needle Spring
Needle
1. Remove retaining ring, aircap, air
flow ring, aircap spring, noz zle,
ma te ri al control knob, needle spring,
and needle as sem bly (Fig. 2).
2. Install appropriate needle/nozzle
assembly se lect ed for material to be
sprayed.
3. Reassemble needle assembly, needle
spring, ma te ri al con trol knob, nozzle,
air flow ring, aircap spring, aircap,
and retainer ring.
The four raised
bumps on the air
flow ring must be facing forward when
as sem bled.
AIR CONTROL VALVE ATTACHMENT
(FIGURE 3)
1. Remove female quick connect fitting
from hose.
2. Screw female quick connect onto air
control valve (included).
3. Screw air control valve onto hose.
4. Attach gun to hose at quick connect
fitting.
The female
quick-connect
fitting outer sleeve is spring load ed and
must be pulled back to be attached or
removed from the gun (Fig. 2).
Air Control
Valve
Hose
Figure 3 - Air Control Valve
Material
Control
Knob
and
Insert
Female
Quick
Connect