Inserting/Ejecting A Disc; Adjusting The Monitor Viewing Angle; Adjusting The Volume; How To View The Display - Alpine IVA-W203 Manual De Operación

Estación multimedia móvil
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Inserting/Ejecting a Disc

1
Press
on the unit.
The display changes to the EJECT/TILT screen.
2
Insert a disc:
Touch [OPEN] on the EJECT/TILT screen.
The movable monitor will open, then insert a disc into the
disc slot. Inserting a disc will close the monitor
automatically.
Disc Slot
Eject the disc:
Touch [
] of DISC on the EJECT/TILT screen.
The movable monitor will open. Then the disc is ejected.
3
Touch [CLOSE] on the EJECT/TILT screen.
The movable monitor will close.
• Touching [CONTROL] or [RETURN] returns to the earlier main
source screen.
• Do not apply shock to the movable monitor when it is open as it may
result in malfunction of the unit.
• The monitor may be dim during low temperature and immediately
after turning on the power. The brightness will return to normal as
time elapses.
• The monitor will stop at the set tilt angle when closing.
CAUTION
Keep hands (or any other object) away from the monitor while it
is opening or closing to avoid damage or injury. The back of the
movable monitor will get very warm under normal operating
conditions. This is not a malfunction. Do not touch.

Adjusting the Monitor Viewing Angle

Adjust the monitor's angle for better visibility.
1
Press
on the unit.
The display changes to the EJECT/TILT screen.
2
Touch [ ] or [ ] of TILT to adjust the desired
monitor angle.
The monitor angle can be adjusted in 5 stages.
3
Touch [RETURN] to return to the previous screen.
• If the monitor touches an obstacle while the angle is being adjusted,
it will stop immediately.
• The screen color will vary when viewed at certain angles. Adjust the
screen angle for the best viewing position.
• If the voltage of the vehicle's battery power is low, the screen may
blink when the screen angle is changed. This is normal and not a
malfunction.
• Touching and holding [RETURN] for at least 2 seconds will change
to the main source screen.

Adjusting the Volume

Adjust the volume by pressing
Volume decreases/increases continuously by pressing and
holding
or
.
Volume: 0 - 35
• The MUTE function is available on the supplied remote control.
Refer to "Controls on Remote Control" on pages 58-59.

How to view the Display

Soft button operation

• Be sure to touch the button lightly with the pad of your finger on the
display to protect the display.
• If you touch a button and there is no reaction, remove your finger
from the display, and try again.
About the button descriptions used in this Owner's Manual
• Soft buttons, ones found in the display, are shown in bold
enclosed in brackets, [ ] (e.g. [SOURCE]).
• Whenever a soft button and a head unit button have the same
function, the explanations in this Owner's Manual will describe
the function of the soft button.

Recalling the Source

Here is an example explanation for the Radio mode display on how to
recall a source.
1
Touch [SOURCE] on the main screen.
The SOURCE selection screen is displayed.
Display example for SOURCE selection screen
Changes to main source screen
Displays source modes that can be selected
(The kind of source modes that are displayed varies
depending on connection and setting.)
Changes to the REAR selection screen when "Setting
the Picture Output" (page 36) is set to ON.
Returns to the previous screen.
• When the source icon is not displayed on SOURCE selection screen,
it is displayed on the next page.
Touching [ ] on the SOURCE selection screen will display the next
page; touching [ ] will return to the previous page.
or
.
11
-EN

Publicidad

Tabla de contenido
loading

Tabla de contenido