Tailing The Rope; Control Of The Pull; Amount Of Tailing Force; Number Of Wraps Of Rope Around Capstan - Textron GREENLEE Ultra Tugger 6800-22 Manual De Operación

Cable Pulling Principles (cont'd)

Tailing the Rope

The rope must be pulled off of the capstan as the pull
progresses. The rope that has left the capstan is the
"tail." The process of pulling the rope off of the capstan
is called tailing the rope.
The resistance of the cable varies throughout the dura-
tion of the cable pull. Changes in resistance are due to
characteristics of the rope, changes in conduit direction,
and changes in the amount of friction. The "feel" of the
rope provides this information about the pull. This is
called tactile feedback. Adjust the tailing force as neces-
sary to compensate for these changes.

Control of the Pull

Decreasing the tailing force will decrease the pulling
force, until the rope slips on the capstan and the pull
stops. This provides a high level of control over the
progress of the cable pull.
Do not allow the rope to slip on the capstan for more
than a few moments. If it becomes necessary to com-
pletely stop a pull, shut off the puller and maintain
enough tailing force to hold cable in place. Tie the rope
off to hold it in place. Use the rope tie-off to hold it in
place.

Amount of Tailing Force

While the rope and cable are under tension, it is im-por-
tant to maintain the proper amount of tailing force.
Too little tailing force will allow the rope to slip on the
capstan. This will build up excessive heat and acceler-
ate rope wear, increasing the possibility of breaking the
rope.
The proper amount of tailing force will stop the rope
from slipping on the capstan and produce a sufficient
amount of pulling force to pull in the rope and cable.
Too much tailing force is any amount more than is nec-
essary to stop the rope from slipping on the capstan.
Excessive tailing force will not increase the pulling force
or pulling speed.
Greenlee / A Textron Company
6800-22 Ultra Tugger
24
Cable Puller and Pulling Package
®
Number of Wraps of Rope Around the Capstan
An experienced operator should choose the number
times the rope is wrapped around the capstan.
The proper number of wraps allows the operator to
control the progress of the pull with a comfortable
amount of effort.
Using too few wraps requires a large tailing force to
accomplish the pull. Using too few wraps also makes
the rope more likely to slip on the capstan. This builds
up heat and accelerates rope wear.
Using too many wraps causes the rope to grab the
capstan tighter. This accelerates rope wear, wastes
power, and increases the possibility of a rope overlap.
Using too many wraps also reduces tactile feedback, so
you receive less information about the pull. You cannot
quickly relax the tailing force when there are too many
wraps.
If the rope becomes difficult to tail, add another wrap
of rope. Turn off the puller and release all of the tension
in the rope. Add a wrap and resume pulling. Be aware,
however, that some pulls will require tension to hold
the cables in place. In these cases, do not attempt to
release all of the tension and add a wrap of rope. You
will need to anticipate the number of wraps before start-
ing the pull.

Preventing Rope Overlap

Do not allow the rope to become overlapped on the
capstan during a pull.
A rope overlap will make it will impossible to continue or
back out of the pull.
If the rope becomes overlapped, you will lose control
of the pull —the rope will advance with no tailing force
and will not feed off of the capstan. The capstan will not
allow you to reverse the direction of the rope, so you
cannot back out of an overlap.
Set up the puller properly. The rope ramp and tapered
capstan are intended to prevent rope overlap. See the
instructions in the Operation section of this manual.
Every wrap of the rope must remain in direct contact
with the capstan. During the pull, take great care to
prevent the incoming rope from riding up and overlap-
ping the next wrap. If an overlap begins to develop,
immediately relax the tailing force on the rope so that
the rope can feed back toward the conduit or tray.
When the rope resumes its normal path, apply tailing
force and continue the pull.
There is no suggested remedy for a rope overlap.
Do not allow the rope to overlap!
4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070