Intended Use; Power Supply - Makita M9800 Manual De Instrucciones

ENGLISH ( Original instructions)
SPECIFICATIONS
Model:
O sc illation per minute
O sc illation angle, lef t/ righ t
O v erall length
Net w eigh t
S af ety c lass
• Due to our continuing program of research and development, the specifications herein are subject to change
w it h out noti c e.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s). The lightest and heaviest combination, according to
EPTA-Procedure 01/2014, are shown in the table.

Intended use

T h e tool is inten d e d f or sa w ing an d c utting w oo d ,
plasti c , g y psum, non- f errous metals, an d f astening
elements ( e. g. un h ar d ene d nails an d staples ) . I t is also
inten d e d f or w orking so f t w all tiles, as w ell as d r y san d -
ing an d s c raping o f small sur f a c es. I t is espe c iall y f or
working close to edge and flush cutting.
Pow er supply
The tool should be connected only to a power supply of
t h e same v oltage as in d i c ate d on t h e nameplate, an d
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
f rom so c kets w it h out eart h w ire.
Noise
Work mode Sound pres-
sure level
( L ) :
pA
S and ing 78 d B( A )
Cutting with 79 d B( A )
plunge c ut
saw blade
Cutting with 79 d B( A )
segmental
saw blade
S c raping 78 d B( A )
T h e noise le v el un d er w orking ma y e x c ee d 8 0 d B ( A ) .
Vibration
The following table shows the vibration total value (tri-axial vector sum) determined according to applicable standard.
S and ing ( a )
h
Cutting with plunge cut saw blade (a
Cutting with segmental saw blade (a
S c raping ( a )
h
Uncertainty ( K ) Applicable
standard
3 d B( A ) EN6 28 4 1 -2-4
3 d B( A ) EN6 28 4 1 -1
3 d B( A ) EN6 28 4 1 -1
3 d B( A ) EN6 28 4 1 -1
Work mode
)
h
)
h
1 5 ,000 - 22,000 min
NOTE: T h e d e c lare d noise emission v alue ( s ) h as
been measured in accordance with a standard test
method and may be used for comparing one tool with
anot h er.
NOTE: T h e d e c lare d noise emission v alue ( s )
may also be used in a preliminary assessment of
e x posure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the po w er tool can differ from the declared
value ( s ) depending on the w ays in w hich the
tool is used especially w hat kind of w orkpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use ( taking account of all parts of the operating
cycle such as the times w hen the tool is s w itched
off and w hen it is running idle in addition to the
trigger time ) .
Vibration emission
2
2.5 m/ s
2
8 .0 m/ s
2
4 .0 m/ s
2
9 .5 m/ s
4 ENGLISH
M9800
-1
1 .6 ° ( 3.2 ° total)
28 3 mm
1 .2 - 1 .3 kg
/ I I
Uncertainty ( K ) Applicable standard
2
1 .5 m/ s EN6 28 4 1 -2-4
2
1 .5 m/ s EN6 28 4 1 -1
2
1 .5 m/ s EN6 28 4 1 -1
2
1 .5 m/ s EN6 28 4 1 -1