Akron STYLE 3000 AEROMASTER 12 Instrucciones De Instalación, Funcionamiento Y Mantenimiento página 15

Right Soft Limit Position (Blink Code 1-1)
. In.this.mode,.Right,.Left,.Up.and.Down.functions.will.be.active . . Move the monitor to the position that is to be set as the Right
Soft Limit. When in the desired position, press the Fog switch..The.new.Right.Soft.Limit.is.now.set.and.the.Left.Soft.Limit.is..
. active.for.programming . . Alternatively,.activating.the.Stream.command.will.abort.this.mode.without.storing.the.position.and.the..
. Left.Soft.Limit.Position.mode.will.be.automatically.selected .
Left Soft Limit Position (Blink Code 1-2).
. In.this.mode,.Right,.Left,.Up.and.Down.functions.will.be.active . . Move the monitor to the position that is to be set as the Left
Soft Limit. When in the desired position, press the Fog switch. The.new.Left.Soft.Limit.is.now.set.and.the.Up.Soft.Limit.is.active..
. for.programming . . Alternatively,.activating.the.Stream.command.will.abort.this.mode.without.storing.the.position.and.the.Up.Soft. .
. Limit.Position.mode.will.be.automatically.selected .
Up Soft Limit Position (Blink Code 1-3)
. In.this.mode,.Right,.Left,.Up.and.Down.functions.will.be.active . . Move the monitor to the position that is to be set as the Up
Soft Limit. When in the desired position, press the Fog switch..The.new.Up.Soft.Limit.is.now.set.and.the.Down.Soft.Limit.is..
. active.for.programming . . Alternatively,.activating.the.Stream.command.will.abort.this.mode.without.storing.the.position.and.the..
. Down.Soft.Limit.Position.mode.will.be.automatically.selected .
Down Soft Limit Position (Blink Code 1-4)
. In.this.mode,.Right,.Left,.Up.and.Down.functions.will.be.active . . Move the monitor to the position that is to be set as the Down
Soft Limit. When in the desired position, press the Fog switch..The.new.Down.Soft.Limit.is.now.set.and.the.Monitor.Orientation. .
. is.active.for.programming . . Alternatively,.activating.the.Stream.command.will.abort.this.mode.without.storing.the.position.and..
. the.Monitor.Orientation.mode.will.be.automatically.selected .
Monitor Orientation (Blink Code 1-7).
. There.are.instances.when.it.is.desirable.to.mount.the.monitor.other.than.in.the.factory.default."flange.on.the.bottom".position . . .
. In.those.instances,.this.function.prevents.having.to.change.the.wiring.of.switches.or.re-programming.CAN.joysticks.to.handle..
. changes.in.Up/Down.–.Left/Right.behavior . . It.is.only.necessary.to.program.the.monitor.orientation.when.the.monitor.is..
. mounted.on.its.side.or.upside.down . . When.in.this.mode,.determine.which.of.the.four.inputs.(Up,.Down,.Left,.or.Right).results..
. in."Up".movement . . The.last.movement.made.prior.to.pressing.the.Fog.switch.will.be.used.as.the.new."Up".motion.and.will.remap..
. the.other.inputs.accordingly . . Move the monitor in whatever the current "Up" motion is and then press the Fog switch. The
new Monitor Orientation is now set and the Position Sensor "Zero" is active for programming..If.the.Stream.switch.is.pressed..
. at.any.time.before.the.Fog.switch,.the.Monitor.Orientation.will.remain.unchanged.and.the.Position.Sensor."Zero".mode.will.be..
. automatically.selected . . NOTE: Use of this function will clear all stored obstacle avoidance profile data and require the
obstacle avoidance option to be reprogrammed.
Position Sensor "Zero" (Blink Code 1-8)
. It.is.often.difficult.for.the.vehicle.manufacturer.to.mount.the.monitor.in.the.precise.position.where."straight.ahead.and.level"..
. matches.the.calibration.of.the.monitor.at.the.Akron.Brass.factory . . Use.of.this.mode.allows.the.user.to."re-zero".the.sensors.at..
. the.desired."straight.ahead.and.level".position . . First, use the Left/Right and Up/Down switches to position the monitor
"straight ahead and level". When the desired position has been reached, press the Fog switch. The new "zero" position is now
set and the Restore Factory Defaults mode is now active for programming..If.the.Stream.switch.is.pressed.at.any.time.before..
. the.Fog.switch,.the.position.sensor.values.will.remain.unchanged.and.the.Restore.Factory.Defaults.mode.will.be.automatically..
. selected . . NOTE: The soft limits positions, stow/deploy positions and CAN position reporting will be impacted by "re-zeroing".
If "re-zeroing" is needed, do so before setting soft limit, stow or deploy positions. NOTE: Use of this function will clear all
stored obstacle avoidance profile data.
Page.13