Keeper KW17.5 Manual De Instrucciones página 5

Winch Installation (Continued)
! !
WARNING
USE ONLY 3/8" -16 UNC BOLT AND NUTS WITH MINIMUM ISO GRADE 8.8.
! !
WARNING
Batteries contain gases, which are flammable and explosive. WEAR EYE PROTECTION DURING INSTALLA-
TION AND REMOVE ALL METAL JEWELRY. Do not lean over battery while making connections.
! !
WARNING
Ensure that the wiring harness does not interfere or come in contact with any hot or moving engine, suspension,
steering, braking or exhaust parts.
MINIMUM ELECTRICAL REQUIREMENTS ARE 60 AMP ALTENATOR AND BATTERY WITH 650 CCA
(COLD CRANKING AMP) CAPACITY.
Step 2 Follow electrical connection diagram
(FIGURE 9). Bolt the circuit breaker to the
terminal end of the Red 2 GA battery lead
that is factory connected to the sealed
solenoid switching pack. Now connect
the circuit breaker to the positive
battery terminal.
Step 3 Connect Black 2 GA battery lead to the negative motor terminal located on the bottom of the motor
and also connect the Black 2 GA ground lead from the solenoid pack to the same negative motor
terminal.
Step 4 Connect the other terminal end of the Black 2 GA battery lead to the negative battery terminal.
If longer wiring harness is required then purchase KWA14607
Step 5 Remove the dust cover on the plug receptacle and insert the plug end of the handheld pendant
switch. The plug end is keyed and will fit easily onto the socket only one way. DO NOT FORCE.
Step 6 Lift and turn the freespool clutch handle to the Disengage position (See FIGURE 12). Pull 5 feet of
wire rope off the drum. Return the freespool clutch handle back to Engaged position. Activate the
Winch cable in and out by momentarily pressing the handheld pendant switch to check drum rotation
direction. The switch is labeled "IN" for winching in and "OUT" for winching out. When released
the switch will automatically go to the off position. IF THIS DOES NOT OCCUR THEN REMOVE THE
HAND HELD PLUG FROM THE RECEPTACLE.
If the drum rotates in the wrong direction then check the trouble shooting area in this manual or call
for assistance 800-533-7372. or contact winches@hamptonproducts.com
Step 7 You are now ready to winch. Practice winching operations by freespooling cable out and winching in
under low loads. Make sure all wraps are wound on tight and close against the previous wrap. Plan
some tests in advance and learn to watch and listen. Recognize the sound of a light steady pull, a
heavy pull and sounds caused by load jerking or shifting. You will gain confidence. ALWAYS WEAR
SAFETY GLASSES, LEATHER GLOVES AND USE THE HAND SAVER STRAP (FIGURE 4).
8
FIGURE 9
Circuit
Breaker
Red 2GA Positive
Battery Terminal
Lead
Black 2GA
Negative
Battery Lead
Pendant Operation
The handheld pendant switch activates a solenoid
that activates power to the winch motor.
To connect the handheld pendant switch, remove
the cover on the plug receptacle and insert the plug
end of remote switch (See Figure 10). The plug on
the pendant control cord is keyed and will fit into the
socket only one way.
The switch trigger returns to the "Off" position when
released. To change direction, move the toggle in the
other direction. (See Figure 10).
The red push button activates the LED work light.
! !
CAUTION
The switch assembly must be kept free of dirt and
moisture to ensure safe operation.
Wireless Operation (Remote KTA14126)
Plug the receiver into the five pin plug located on the winch control box (Where the hand held control usually
plugs into). Please take care to line up the keyed notch on the inside of the receiver with the keyway on the
outside of the plug (See FIGURE 11). Your are now ready to remotely operate the winch.
Make sure notch fits into key way as misalignment will damage the unit and void warranty.
Black 2 GA
Ground Lead
Please note that the unit is programmed for a 1 second delay in both starting and stopping. This may
represent a 6" to 8" travel in the wire rope.
Your wireless remote is now installed. Enjoy your wireless remote switch winching experience.
Wire
Rope
IN
FIGURE 10
Wire
Rope
FIGURE 11
OUT
Wireless
Receiver
Key
Slot
IN
OUT
Key
Slot
9