Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
ADDITIONAL CUSHIONS:
You may add additional cushioning to the chair with your own pil-
lows. Keep in mind that the more cushioning you add, the less you
will be able to feel the massage.
Adjusting the Backrest Angle
You can adjust the backrest angle to recline up to approximately
Figure 10
165 degrees. Reclining the backrest increases the intensity of the
massage, and also repositions the body so that the massage range
along your back and neck is changed. Typically, the further you
recline, the further the massage will reach in the shoulder and neck
area. Reclining the chair fully is the best way to experience a neck
massage.
RECLINE
To recline the backrest using the manual control, lift the lever on the
right side of the chair seat (Fig. 10) and lean back. When you are
in the desired position, release the lever.
Figure 11
When you are ready to raise the backrest, pull the lever up again
and lean forward. The hydraulic gas system will raise the backrest
for you.
ADJUSTING THE FOOTREST
To raise the footrest, pull up on the footrest lever located on the left
side of the chair seat (Fig. 11). Relax your legs so they do not pro-
vide extra resistance. The hydraulic cylinder will begin to raise the
footrest. When you have reached the desired position, release the
lever.
To lower the footrest, make sure the backrest of your chair is in the
upright position. Pull up on the footrest lever and gently push
down with your legs until the footrest is lowered. Release the lever
when finished.
It is recommended that you elevate your feet while the backrest is
reclined to avoid strain on the lower back. It is also best to elevate
your feet during a massage session to promote circulation.
NOTE: In order to avoid strain and potential injury to your back,
never attempt to get in or out of the massage chair with the
backrest reclined or the footrest raised. Make sure the chair is
the closed (lowered) position.
8
Remote Control Overview
Master Controls
The master controls turn on power for the massage, and also allow you to pause a
massage without turning it off or having to start over. These buttons will override
any other function on the remote control for safety purposes.
Programmed Massage Sessions
The pre-programmed massage sessions are 12-15 minutes each. Just push a pro-
gram button and sit back and enjoy. Once the program is finished, the massage
system will automatically shut off. You can activate the massage system again by
pushing any button.
Manual Controls
Instead of using a program, you can select a specific massage function using
these buttons. Once you have selected a function, it will stay in that mode until you
push another function or turn the massage system off.
Note: The massage system will completely shut off 20 minutes after the last
command for safety purposes. However, it will not shut off if the last com-
mand was a programmed massage session.
1
2
3
2
1
3
4
6
4
5
6
5
7
7
10
8
8
9
9
10
11
12
11
13
12
15
16
13
14
14
15
16
9
Power – To turn the massage chair on or off.
Pause – To pause the current operation in place.
Demo – To activate a brief preset course of
the massage functions.
Energize – To activate a preset, energizing
massage program for the entire back.
Relax – To activate a preset, relaxing
massage program for the entire back.
Upper – To activate a preset massage
program for the upper section of the back.
Lower – To activate a preset massage
program for the lower section of the back.
Full Knead – To activate the kneading
function.
Full Roll – To activate the rolling function.
Full Tap – To activate the tapping function.
Spot Knead – To activate the stationary
kneading function.
Spot Tap – To activate the stationary tap-
ping function.
Adjust Up – To adjust the massage roller
up during a stationary function.
Adjust Down - To adjust the massage
rollers down during a stationary function.
Speed – To adjust the speed of the massage.
Width – To adjust the width of the massage.
Publicidad
Tabla de contenido
