LEGRAND Pass & Seymour RWC826USB Manual De Instrucciones

No: 341195 – 04/17
Catalog Number(s) • Les Numéros de Catalogue: RWC826USB
Country of Origin: Made in China • País de origen: Hecho en China
Receptacle: 15amp, 125VAC
USB: Class 2, 5Vdc, 3.1A
Wireless Nominal Output: 5V, 1A
DESCRIPTION: This device is a radiant
charging Wall Plate. The USB provides 3.1A total DC power at 5 Volts for charging USB devices and
supplies power to the wireless charger. The USB port is for charging purpose only and is not intended for
data transfer. The wireless charger works with all phones equipped with a Qi receiver.
Qi STANDARD:
• Qi (pronounced "chee") is the global standard for
compatible wireless charging.
• Just like Bluetooth set the standard for
®
exchanging data over short distances or Wi-Fi™
set the standard for wireless networking, Qi sets
the standard for wireless charging.
• To charge, you just place a Qi-enabled device on
a Qi charging surface, there are no cords to plug
into the phone.
• To find Qi compatible devices, go to: https://www.
wirelesspowerconsortium.com/products
Fits Single Gang Electrical Box
READ & SAVE THESE INSTRUCTIONS!
CAUTION:
• To prevent severe shock or electrocution, always turn power
OFF at the service panel before working with wiring.
• Use this device with copper or copper-clad wire. Do not use with
aluminum wire.
• Must be installed in accordance with National and Local
electrical codes.
• All cables should be routed away from the outlet openings.
• Outlets are not intended to support devices or appliances.
Do not hang devices by charging cord.
WARNING: IMPROPER WIRING OF ANY ELECTRICAL DEVICE
CAN CAUSE SERIOUS INJURY OR DEATH. THESE WIRING
DEVICES SHOULD BE INSTALLED BY AN ELECTRICIAN OR
OTHER QUALIFIED PERSON.
Tomacorriente: 15 A, 125 V CA
USB: Clase 2, 5 V CC, 3,1 A
Salida nominal inalámbrica: 5 V, 1A
Duplex Receptacle with USB charger along with a Wireless
®
HOW Qi WORKS:
• Qi works by generating a safe electromagnetic
field between a charger and a device through a
well-established process called magnetic induction.
Magnetic induction has been used for more than a
century to make power transformers.
• Qi chargers have a built-in transmitting coil that
intelligently communicates with Qi devices using
a specific electromagnetic frequency, so any Qi
device will work with any Qi charger, now and in
the future.
Pass & Seymour
radiant ® Duplex Receptacle with 3.1A USB and Wireless Charging Wall Plate
for 1 gang box installation
Tomacorriente dúplex radiant ® con placa de pared de carga mediante USB e
inalámbrica de 3,1 A para la instalación de uns caja de distribución eléctrica
Installation Instructions • Instrucciones de Instalación
LEA Y GUARDE ESTAS INSTRUCCIONES.
PRECAUCIÓN:
• Para evitar serios electrochoques o electrocución, siempre
APAGUE el suministro eléctrico en el panel de servicio antes de
trabajar con los cables.
• Utilice este dispositivo con alambres de cobre o revestidos de
cobre. No usar con cables de aluminio.
• Se debe instalar de acuerdo con los códigos eléctricos
nacionales y locales.
• Todos los cables deben ser alejados de la abertura de la salida.
• Las salidas no tienen el objeto de admitir dispositivos o
electrodomésticos. No use el cable de carga para colgar
los dispositivos.
ADVERTENCIA: EL CABLEADO INCORRECTO DE UN
DISPOSITIVO ELÉCTRICO PUEDE CAUSAR LESIONES
GRAVES O AÚN LA MUERTE. UN ELECTRICISTA U
OTRA PERSONA COMPETENTE DEBE INSTALAR ESTOS
DISPOSITIVOS DE CABLEADO.
INSTALLATION INSTRUCTIONS:
1. Disconnect power to circuit by removing fuse or turn circuit breaker OFF
before installing. Before wiring, verify that power has been removed by
testing with a circuit tester at the outlet box.
2. To replace existing device, remove wall plate and pull device from box.
If new installation, skip to step 5.
3. Label wires connected to existing device.
4. Disconnect existing power.
5. Strip wires to length 1/2" using gauge located on back of the device.
Use #14 - #10 AWG solid or stranded copper wire.
6. Install device per corresponding wiring diagram, see Figure 1.
7. Torque terminal screws to 12-14 inch-pounds.
8. Mount device to the wall box, ensure "UP" arrows are oriented properly.
9. Snap wall plate with integral wireless charger to device and restore
power to circuit.
LED
Color Standby
Green Off
Red Off
®
Figure 1
Operational Status
Transfer Complete Fault
Off On Blink Slow
On Off Blink Slow