Lutron GRAFIK Eye GRX-CCO-8 Manual De Instrucciones página 6

6. Exit Programming Mode.
I Press and hold the Program Button on the GRX-CCO-8 for about 3 seconds, until the Status LED
starts blinking and the Output Status LEDs stop cycling.
Assign GRX-CCO-8 to GRX Control Units (Scene Control)
1. Enter Programming Mode
I Press and hold the Program Button on the GRX-CCO-8
for about 3 seconds, until the Status LED stops blinking
and all Output Status LEDs begin cycling.
2. Assign GRX-CCO-8 to GRX Control Unit
I Press and hold the Scene 1 button on the desired GRX
Control Unit to which the GRX-CCO-8 will be assigned
until the Scene LEDs flash in unison. (Press the Off but-
ton to unassign the GRX-CCO-8). See diagram at right.
3. Assign GRX-CCO-8 to remaining GRX Control Units
I Repeat the Step 2 for each GRX Control Unit to which the
GRX-CCO-8 will be assigned.
4. Exit Programming Mode
I Press and hold the Program Button on the GRX-CCO-8
for about 3 seconds, until the Status LED starts blinking
and the Output Status LEDs stop cycling.
LIMITED WARRANTY
Lutron will, at its option, repair or replace any unit that is defective in materials or manufacture within one year after purchase. For warranty service, return unit to place of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA
18036-1299, postage pre-paid.
This warranty is in lieu of all other express warranties, and the implied warranty of merchantability is limited to one year from purchase. This warranty does not cover the cost of installation, removal or reinstallation, or dam-
age resulting from misuse, abuse, or improper or incorrect repair, or damage from improper wiring or installation. This warranty does not cover incidental or consequential damages. Lutron's liability on any claim for dam-
ages arising out of or in connection with the manufacture, sale, installation, delivery, or use of the unit shall never exceed the purchase price of the unit.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Some
states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
National Electrical Code is a registered trademark of the National Fire Protection Association, Inc.
Lutron and GRAFIK Eye are registered trademarks of Lutron Electronics Co., Inc.
© 2003 Lutron Electronics Co., Inc.
Internet: www.lutron.com
E-mail: product@lutron.com
Lutron Electronics Co., Inc.
Made and printed in U.S.A.
P/N 040-205 Rev.A 6/03
Status LED
Program Button
1 2 3 4 5
ADDRESS
00
ZONES
M S
MASTER
Scene 1
Button
Off Button
Scene LEDs
World Headquarters
Lutron Electronics Co. Inc.,
TOLL FREE: (800) 523-9466
(U.S.A., Canada, Caribbean)
Tel: (610) 282-3800;
International 1- 610-282-3800
Fax: (610) 282-3090;
International 1-610-282-3090
European Headquarters
Lutron EA Ltd.,
FREEPHONE: 0800 282107 (U.K.)
Tel: (171) 702-0657;
International 44-702-702-0657
Fax: (171) 480-6899;
International 44-702-480-6899
ASIAN HEADQUARTERS
Lutron Asuka Co, Ltd.,
TOLL FREE: (0120) 083417 (Japan)
Tel: (03) 5575-8411;
International ++81-3-5575-8411
Fax: (03) 5575-8420;
International ++81-3-5575-8420