Publicidad
Idiomas disponibles
Idiomas disponibles
2. Inflate the boat in the order of inflation as shown on the capacity plate printed on the boat (see also figure # 1 –
numbering of the valves).
3. Max. air pressure : The correct pressure for this item is : 0,06 bar (= 60 mBar). Do not exceed it. Your boat
features a SEVYTEST pressure indicator which indicates the proper pressure : First inflate the safety chamber
(see figure # 1) until "A" marking and then the main chamber (see figure # 1) until "B" marking is reached.
Overpressure : deflate until you reach the recommended pressure. Drop of pressure : inflate again slightly.
NOTICE : PVC material extending under the inflation pressure, after many inflations the Sevytest gauge may not
return to its initial position but it still will allow you to check that the gauge remains within the recommended
If you leave your product exposed to the hot sun check the pressure and deflate it slightly, otherwise the
material might be overstretched.
The ambient temperature affects the tube's internal pressure : a variation of 1°C causes a variation of the pressure in
the tube of +/- 4 mBar.
OPERATING INSTRUCTIONS
Use the boat only in protected shore-zones, avoid open water and streams with strong currents.
BEWARE OF OFFSHORE WINDS AND CURRENTS !
Get informed on local regulations and hazards related to water activities and boat operation.
Before using the product, please check it carefully.
A bad distribution of the load can destabilize the boat and may result in a loss of control.
Always wear a coast guard approved Personal Flotation Device.
Do not exceed the authorized number of persons or weight.
Avoid all contact between the buoyancy tubes and sharp objects or aggressive liquids (such as acid).
This product is equipped with ropes. Keep the ropes away from children.
If, after an accident, a compartment deflates, bring it inside the boat and return at reduced speed. The boat is kept over
water by the security system and by the strong buoyancy.
MAINTENANCE : DEFLATING – FOLDING THE ITEM – CLEANING – WINTERING STORAGE
1. Remove oars/paddles and other accessories.
2. To deflate, unscrew the valve insert and open the valve(s) cap of the other valves.
3. Clean and check the item as well as all the accessories after each use. Rinse it thoroughly making sure to remove
any residues of salt if used in salt water. Use a mild soapy solution, do not use detergents or any type of silicone-
based products. Make sure that the product is completely dry before putting it away.
4. Fold the sides into the middle, then roll it up from the opposite end of the valves (so remaining air can escape from
the valves); start again if you feel there is still some air in the tubes.
5. When storing your inflatable, keep it in a clean and dry place that is not affected from major variations in temperature
and other damaging factors. You may store it deflated and rolled up in a bag or assembled and lightly inflated. Store
it away from rodents.
HOW TO REPAIR SMALL PUNCTURES
You can repair small punctures with the included repair kit (Note: Glue not included in USA). Please note that in order
for the repair to be successful, the humidity level should be less than 60%, temperature between 65° F/77° F or
18°C/25° C. Avoid carrying out repairs in the rain or in direct sunlight. Check that the tube is fully deflated and lies flat.
1. Draw the shape of the patch exactly where it will be applied, cut a round patch at least 2" / 5 cm larger than the
cut/damaged area.
2. Clean the damaged area and the corresponding side of the patch with a grease remover of the alcohol type and
allow for it to dry for 5 minutes.
3. Apply 3 thin layers of glue on both the patch and the damaged area, allow for it to dry for 5 minutes between layers
until the glue feels tacky.
4. When the third layer of glue is dry, apply the patch without pressing and adjust the positioning if required, press the
air bubbles which may have formed under the patch by smoothing the patch with a round object such as a spoon, do
this procedure by starting in the center of the patch towards the outside, clean the excess glue with a solvent.
Drying : 12 hours.
Perform all of your repairs in a well-ventilated area.
Avoid inhaling glue vapors or swallowing.
N.B. the repairs on the weldings must not be glued. Only the manufacturer of the boat can perform the repairs on the
weldings.
WARNING !
WARNING !
WARNING !
Avoid contact with the skin or the eyes.
Keep all repair materials (glue, solvents, etc.)
away from children's reach.
5
zone.
E
N
G
L
I
S
H
Publicidad
