Craftsman professional 152.217050 Manual De Instrucciones página 3

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

GENERAL
SAFETY
INSTRUCTmONS
Operating a Jointer/Haner
can be dangerous if safety
and common sense are ignored, The operator must be
familiar with the operation of the tool Read this manuaU
to understand this Jointer/Haner,
DO NOT operate this
Jointer/Haner
if you do not fully understand the Hmita-
tions of this tool DO NOT modify this Jointer/Haner
in
any way,
BEFORE
USUNG THE JOINTER/PLANER
9,
ALWAYS WEAR EYE PROTECTION,
Any power
tooUcan throw debris into the eyes during opera-
tions, which couUd cause severe and permanent
eye damage, Everyday eyegUasses are NOT safety
gUasses, ALWAYS wear Safety Goggbs
(that
compUy with ANSi standard Z87,1) when operating
power toob, Safety Goggbs are avaHabb at Sears
Retail Stores,
To avoid serious injury and damage to the tool, read
and follow all of the Safety and Operating Instructions
before operating the Jointer/Haner,
2,
3,
4,
5,
READ the entire Owner's Manual, LEARN how to
use the tool for its intended applications,
GROUND ALL TOOLS, If the tool is supplied with
a 3-prong plug, it must be plugged into a 3-contact
electrical receptacle, The 3rd prong is used to
ground the tool and provide protection against
accidental electric shock, DO NOT remove the 3rd
prong, See Grounding Instructions,
AVOID A DANGEROUS WORKING
ENVIRON-
MENT. DO NOT use electrical tools in a damp
environment or expose them to rain,
DO NOT use electrical tools in the presence of
flammable liquids or sasses,
ALWAYS keep the work area clean, well lit, and
organized, DO NOT work in an environment with
floor surfaces that are slippery from debris, grease,
or wax,
6,
7,
KEEP VISITORS AND CHILDREN AWAY, DO NOT
permit people to be in the immediate work area,
especially when the electrical tool is operating,
DO NOT FORCE THE TOOL to perform an opera°
tion for which it was not designed, It will do a safer
and higher quality job by only performing operations
for which the tool was intended,
8,
WEAR PROPER CLOTHING. DO NOT wear loose
clothing, gloves, neckties, or jewelry, These items
can get caught in the machine during operations
and pull the operator into the moving parts, Users
must wear a protective cover on their hair, if the
hair is long, to prevent it from contacting any
moving parts,
10,
11,
12,
13,
14,
ALWAYS WEAR HEARING PROTECTION,
Plain cotton is not an acceptable protective device,
Hearing equipment should comply with ANSI $3,19
Standards,
ALWAYS UNPLUG THE TOOL FROM THE ELEC-
TRICAL RECEPTACLE when making adjustments,
changing parts or performing any maintenance,
KEEP PROTECTIVE GUARDS IN PLACE AND IN
WORKING ORDER,
AVOID ACCIDENTAL STARTING, Make sure that
the power switch is in the "OFF" position before plugo
gins in the power cord to the electrical receptacle,
REMOVE ALL MAINTENANCE
TOOLS from the
immediate area prior to turning "ON" the Jointed
Planer,
15, USE ONLY RECOMMENDED
ACCESSORIES,
Use of incorrect or improper accessories could
cause serious injury to the operator and cause
damage to the tool, If in doubt, check the instruction
manual that comes with that particular accessory,
16, NEVER LEAVE A RUNNING TOOL UNATTENDED,
Turn the power switch to the "OFF" position, DO
NOT leave the tool until it has come to a complete
stop,
17, DO NOT STAND ON A TOOL, Serious injury could
result if the tool tips over or you accidentally contact
the tool,
18, DO NOT store anything above or near the tool where
anyone might try to stand on the tool to reach it,
19, MAINTAIN YOUR BALANCE. DO NOT extend your°
self over the tool, Wear oil resistant rubber-soled
shoes, Keep floor clear of debris, grease, and wax,
20, MAINTAIN TOOLS WITH CARE, Always keep tools
clean and in good working order, Keep all blades
and tool bits sharp
SAVE THESE INSTRUCTIONS.

Publicidad

Tabla de contenido
loading

Tabla de contenido