Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

IB506003EN
Installation Instructions - NFFLD-S/UFLD-S
Instructions d'installation – NFFLD-S/UFLD-S
Instrucciones de instalación de la luminaria NFFLD-S/UFLD-S
WARNING
Make certain power is OFF before starting installation
or attempting any maintenance.
WARNING
Risk of fire/electric shock. If not qualified, consult an
electrician.
WARNING
Risk of Electric Shock – Disconnect power at fuse or
circuit breaker before installing or servicing.
WARNING
Risk of Personal Injury – Fixture may become damaged
and/or unstable if not installed properly.
Do not mount luminaire within 6" of a
combustible surface.
Do not handle luminaire by the glass. Do not
touch LEDs.
IMPORTANT: Read carefully before installing fixture. Retain for future reference.
GENERAL: Upon receipt of the fixture, thoroughly inspect for any freight damage which should be brought to the
attention of the delivery carrier. Compare the catalog description listed on the packing slip with the fixture label on the
housing to assure you have received the correct material.
SAFETY: This fixture must be wired in accordance with the National Electrical Code and applicable local codes and
ordinances. Proper grounding is required to insure personal safety. Carefully observe grounding procedure under
installation section.
APPLICATIONS: This lighting fixture is designed for outdoor lighting services, and should not be used in area of limited
ventilation or inside high ambient temperature enclosures. It must be stored in a dry location prior to installation. Do
not expose lighting fixture to rain, dust or other environmental conditions prior to installation and insertion of photo
control or shorting cap (if so equipped). Do not install the fixture near combustible materials or locate next to airflow
blocking surfaces within 6 inches. Best results will be obtained if installed and maintained according to the following
recommendations.
WARNING
Risk of Burn – Disconnect power and allow fixture to
cool before servicing.
N
ote:
These instructions do not claim to cover all
details or variations in the equipment, procedure,
or process described, nor to provide directions
for meeting every possible contingency during
installation, operation or maintenance. When
additional information is desired to satisfy a
problem not covered sufficiently for user's purpose,
please contact your nearest representative.
N
ote:
This lighting fixture has been shipped complete
with one of several mounting options. Please follow
the installation instructions specific to the catalog
part that you ordered.
N
ote:
Care must be taken not to set lighting fixture down
on optical lenses or lift the fixture in the lens area.
N
ote:
Specifications and dimensions subject to change
without notice.
Brand Logo
reversed out of
black
INS #
INS #

Publicidad

loading

Resumen de contenidos para Eaton NFFLD-S

  • Página 1 IB506003EN INS # INS # Installation Instructions - NFFLD-S/UFLD-S Instructions d’installation – NFFLD-S/UFLD-S Instrucciones de instalación de la luminaria NFFLD-S/UFLD-S WARNING WARNING Make certain power is OFF before starting installation Risk of Burn – Disconnect power and allow fixture to or attempting any maintenance.
  • Página 2 Installation Instructions - NFFLD-S/UFLD-S INSTALLATION This lighting fixture has been shipped complete with one of several mounting options. Please follow the installation instructions specific to the catalog part that you ordered. Tools Required #2 Philips screwdriver, Flat head screwdriver and hex head.
  • Página 3 Installation Instructions - NFFLD-S/UFLD-S Tools Required Philips head screwdriver. Black (+) Line Knuckle Mount (Figure 3.) ote: This configuration is equipped with an adjustable (-) Common White Fixture knuckle which can be mounted directly to the 1/2” NPS access hole in the cover plate of the junction box.
  • Página 4 Installation Instructions - NFFLD-S/UFLD-S Wire Guard Installation (4) Accessory Spacers Tools Required Phillips head screwdriver, Flat head screwdriver. WARNING Make certain power is OFF before starting installation or attempting any maintenance. Make certain all power is OFF before starting installation.
  • Página 5 Installation Instructions - NFFLD-S/UFLD-S Visor Installation Tools Required Phillips head screw driver, Flat head screwdriver. WARNING Make certain power is OFF before starting installation or attempting any maintenance. Make certain all power is OFF before starting installation. Remove the existing (4) black clips on the edge of the lens with flat head screwdriver.
  • Página 6 Instructions d’installation – NFFLD-S/UFLD-S AVERTISSEMENT AVERTISSEMENT Assurez-vous que l'alimentation électrique est COUPÉE Risque de brûlures – Coupez l'alimentation électrique et avant de commencer l'installation ou de procéder à une laissez refroidir le luminaire avant l'entretien. opération d'entretien. Ces instructions ne prétendent pas couvrir emarque: tous les détails ou toutes les variations de...
  • Página 7: Outillage Nécessaire

    Instructions d’installation – NFFLD-S/UFLD-S INSTALLATION Replacez la plaque de recouvrement et resserrez les (2) vis du couvercle à un couple de 1,7 Nm (15 po-lb). Ce luminaire est livré avec une option de montage Serrez les écrous de blocage à 7 ,35 Nm (65 po-lb).
  • Página 8 Instructions d’installation – NFFLD-S/UFLD-S Outillage nécessaire Tournevis à tête cruciforme. alimentation (+) Noire Montage sur articulation (Figure 3). emarque: Cette configuration comprend une articulation Blanche commun (-) Luminaire réglable qui peut être montée directement sur le trou d'accès NPS de 1,3 cm (1/2 po)
  • Página 9 Instructions d’installation – NFFLD-S/UFLD-S emarque: La cellule photoélectrique (non fournie) doit (4) bagues être équipée d'un joint souple élastique d'espacement situé sur la surface inférieure afin d'assurer accessoires l'étanchéité avec le connecteur. Installation de la grille de protection Outillage nécessaire Tournevis cruciforme, tournevis à tête plate.
  • Página 10 Instructions d’installation – NFFLD-S/UFLD-S Installation de la visière Outillage nécessaire Tournevis cruciforme, tournevis à tête plate. AVERTISSEMENT Assurez-vous que l'alimentation électrique est COUPÉE avant de commencer l'installation ou de procéder à une opération d'entretien. Assurez-vous que l'alimentation électrique est COUPÉE avant de commencer l'installation.
  • Página 11 Instrucciones de instalación de la luminaria NFFLD-S/UFLD-S ADVERTENCIA ADVERTENCIA Asegúrese de que la alimentación esté desconectada Riesgo de quemaduras: Desconecte la alimentación antes de comenzar la instalación o intentar realizar el y espere a que se enfríe la luminaria antes de realizar mantenimiento.
  • Página 12: Instalación

    Instrucciones de instalación de la luminaria NFFLD-S/UFLD-S INSTALACIÓN Vuelva a colocar la placa de cubierta y ajuste los (2) tornillos de la cubierta hasta 15 in-lb. Esta luminaria ha sido enviada completa con una de las Ajuste las tuercas de bloqueo hasta 65 in.-lb.
  • Página 13 Instrucciones de instalación de la luminaria NFFLD-S/UFLD-S Herramientas necesarias Destornillador de cabeza Philips. Línea (+) Negro Montaje sobre codo (Figura 3.) ota: Esta configuración viene equipada con un codo Común (-) Blanco ajustable que se puede montar directamente sobre Luminaria el orificio de acceso NPS de 1/2”...
  • Página 14 Instrucciones de instalación de la luminaria NFFLD-S/UFLD-S ota: El fotocontrol (no incluido) debe contener una junta (4) separadores suave y elástica ajustada a la parte inferior de su accesorios superficie para garantizar un apropiado sellado hermético entre el control y el receptáculo.
  • Página 15 Instrucciones de instalación de la luminaria NFFLD-S/UFLD-S Instalación del visor Herramientas necesarias Destornillador de cabeza Phillips, destornillador de cabeza plana. ADVERTENCIA Asegúrese de que la alimentación esté desconectada antes de comenzar la instalación o intentar realizar el mantenimiento. Asegúrese de que toda la alimentación esté APAGADA antes de la instalación.
  • Página 16 Warranties and Limitation of Liability Please refer to www.eaton.com/LightingWarrantyTerms for our terms and conditions. Garanties et limitation de responsabilité Veuillez consulter le site www.eaton.com/LightingWarrantyTerms pour obtenir les conditions générales. Garantías y Limitación de Responsabilidad Visite www.eaton.com/LightingWarrantyTerms para conocer nuestros términos y condiciones.

Este manual también es adecuado para:

Ufld-s