Temperature And Moisture; Ice And Water - KitchenAid KRFC302ESS Instrucciones Para El Usuario

Temperature and Moisture

Temperature is too warm
New installation? Allow 24 hours following installation for the
■
refrigerator to cool completely.
Door(s) opened often or left open? Allows warm air to enter
■
refrigerator. Minimize door openings and keep doors fully
closed.
Large load of food added? Allow several hours for
■
refrigerator to return to normal temperature.
Controls set correctly for the surrounding conditions?
■
Adjust the controls a setting colder. Check temperature in 24
hours. See "Using the Control(s)."
There is interior moisture buildup
NOTE: Some moisture buildup is normal.
Humid room? Contributes to moisture buildup.
■
Door(s) opened often or left open? Allows humid air to enter
■
refrigerator. Minimize door openings and keep doors fully
closed.

Ice and Water

The ice maker is not producing ice or not enough ice
Refrigerator connected to a water supply and the supply
■
shutoff valve turned on? Connect refrigerator to water
supply and turn water shutoff valve fully open.
Kink in the water source line? A kink in the line can reduce
■
water flow. Straighten the water source line.
Ice maker turned on? Make sure wire shutoff arm or switch
■
(depending on model) is in the ON position.
New installation? Wait 24 hours after ice maker installation
■
for ice production to begin. Wait 72 hours for full ice
production.
Freezer door closed completely? Firmly close the freezer
■
compartment door. If the freezer compartment door will not
close all the way, see "The doors will not close completely,"
earlier in this section.
Large amount of ice recently removed? Allow 24 hours for
■
ice maker to produce more ice.
Ice cube jammed in the ice maker ejector arm?
■
Remove ice from the ejector arm with a plastic utensil.
Water filter installed on the refrigerator? Remove filter and
■
operate ice maker. If ice volume improves, then the filter may
be clogged or incorrectly installed. Replace filter or reinstall it
correctly.
Reverse osmosis water filtration system connected to
■
your cold water supply? This can decrease water pressure.
See "Water Supply Requirements."
The ice cubes are hollow or small
NOTE: This is an indication of low water pressure.
Water shutoff valve not fully open? Turn the water shutoff
■
valve fully open.
Kink in the water source line? A kink in the line can reduce
■
water flow. Straighten the water source line.
14
Water filter installed on the refrigerator? Remove filter and
■
operate ice maker. If ice quality improves, then the filter may
be clogged or incorrectly installed. Replace filter or reinstall it
correctly.
Reverse osmosis water filtration system connected to
■
your cold water supply? This can decrease water pressure.
See "Water Supply Requirements."
Questions remain regarding water pressure? Call a
■
licensed, qualified plumber.
Off-taste, odor or gray color in the ice
New plumbing connections? New plumbing connections
■
can cause discolored or off-flavored ice.
Ice stored too long? Discard ice. Wash ice bin. Allow 24
■
hours for ice maker to make new ice.
Odor transfer from food? Use airtight, moisture proof
■
packaging to store food.
Are there minerals (such as sulfur) in the water? A water
■
filter may need to be installed to remove the minerals.
Water filter installed on the refrigerator? Gray or dark
■
discoloration in ice indicates that the water filtration system
needs additional flushing. Flush the water system before using
a new water filter. Replace water filter when indicated. See
"Water Filtration System."
The water dispenser will not operate properly
Refrigerator connected to a water supply and the supply
■
shutoff valve turned on? Connect refrigerator to water
supply and turn water shutoff valve fully open.
Kink in the water source line? Straighten the water source
■
line.
New installation? Flush and fill the water system. See "Water
■
Dispenser."
Is the water pressure at least 35 psi (241 kPa)? The water
■
pressure to the home determines the flow from the dispenser.
See "Water Supply Requirements."
Water filter installed on the refrigerator? Remove filter and
■
operate dispenser. If water flow increases, the filter may be
clogged or incorrectly installed. Replace filter or reinstall it
correctly.
Refrigerator door closed completely? Close the door firmly.
■
If it does not close completely, see "The doors will not close
completely," earlier in this section.
Recently removed the doors? Make sure the water
■
dispenser wire/tube assembly has been properly reconnected.
See "Refrigerator Door(s) and Drawer."
Reverse osmosis water filtration system connected to
■
your cold water supply? This can decrease water pressure.
See "Water Supply Requirements."
Water is leaking from the dispenser system
NOTE: One or two drops of water after dispensing is normal.
Glass not being held under the dispenser long enough?
■
Hold the glass under the dispenser 2 to 3 seconds after
releasing the dispenser lever.
New installation? Flush the water system. See "Water
■
Dispenser."
Recently changed water filter? Flush the water system. See
■
"Water Dispenser."
Water on the floor near the base grille? Make sure the
■
water dispenser tube connections are fully tightened. See
"Refrigerator Door(s) and Drawer."