EINHELL KSE 1435 Manual De Instrucciones página 21

Motosierra eléctrica
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 39
Anl. KSE 1435,1635,1640
31.10.2001 7:57 Uhr
Felling trees
To fell trees, observe all the safety regulations and
proceed as follows:
The chain saw may be used to fell only trees which
are smaller in diameter than the length of the chain
bar. Never try to extract a jammed saw with the
motor still running. If the saw chain gets jammed,
release it using a wooden wedge.
Remember:
Danger zone: Falling trees can bring down
other trees with them. The danger zone is
therefore twice the length of the tree being
felled. (Fig. 11)
Felling trees is dangerous and requires practice.
If you are a beginner or inexperienced, do not try
to teach yourself but seek professional training.
(Fig. 12)
Falling direction:
First estimate the direction of fall, taking into
account the centre of gravity of the crown and the
wind direction. The chain saw must be running
before it comes into contact with the wood. Switch
on the chain saw. Saw an undercut in the tree in
the direction of fall and then make a horizontal cut
(back cut) on the side opposite to the undercut.
Make the undercut: This will give the tree a
direction and guidance.
Check the direction of fall: If you have to correct
the undercut, always recut over the entire width.
Call out „Timber!"
Only now make the back cut, which must be hig
her than the sole of the undercut. Insert wedges
in good time.
Leave the bridge in place as it will function as a
hinge. If you cut through the bridge, the tree will
fall randomly.
Fell the tree by driving a wedge into the back cut,
not by sawing through it.
When the tree falls, step back and watch the crown.
Wait for the crown to stop swinging. Do not continue
working under branches which have got stuck.
Do not fell trees:
if you can no longer distinguish details within the
danger zone, e.g. owing to fog, rain, snow drifts or
twilight,
if the direction of fall cannot be reliably estimated
owing to wind or gusts of wind.
Felling work on sloping ground, black ice, frozen
or dewy ground is safe only if you can get a firm
foothold.
To switch off: Pull the plug out of the power socket.
Seite 21
To fell the tree, you must drive a wedge into the back
cut. When retreating after making the back cut,
watch out for falling branches.
Accessories:
Use only original spare parts:
Chain bar KSE 1435, KSE 1635
45.001.31
Chain bar KSE 1640
45.003.31
Saw chain KSE 1435, KSE 1635
45.001.11
Saw chain KSE 1640
45.003.11
Maintenance and cleaning
Always pull the plug out of the power socket
before doing any work on the machine!
Keep the cooling vents on the motor housing clean
and unobstructed at all times. Only the maintenance
work described in these operating instructions may
be carried out. Any other maintenance work must be
carried out by our Customer Service. Do not modify
the power saw in any way as this could jeopardize its
safety. Should the machine fail despite our careful
manufacturing and inspection procedures, have it
repaired by an authorized Customer Service works-
hop. In the event of any inquiries and spare parts
orders, always quote the type designation and the 9-
digit order number.
Storage
Keep your chain saw in a safe place. The unused
machine should be stored clean, on a flat surface
and in a dry place which is inaccessible to children.
GB
21

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Kse 1635Kse 164045.002.6045.002.5045.002.00

Tabla de contenido