Vimar ELVOX ZR01 Manual Para El Conexionado Y El Uso página 5

APPLICATIONS
The ZR Digital Inductive Loop Detector range is the ideal solution for parking
barrier control, motorized gates and doors, vehicle access control and indu-
strial control systems.
The ZR range is a high performance single or dual channel vehicle detector
packaged in a compact housing, the connection is made with an industrial
standard 11-pin round connector.
Six versions listed below are available, single or dual channel, and 3 possibi-
lities for the power supply :
ZR0/110 : Single loop detector with 110 to 120 Vac power supply
ZR01/220 : Single loop detector with 220 to 240 Vac power supply
ZR01:
Single loop detector with 12 to 24 Vac/dc power supply
ZR02/110 : Dual loop detector with 110 to 120 Vac power supply
ZR02/220 : Dual loop detector with 220 to 240 Vac power supply
ZR02 : Dual loop detector with 12 to 24 Vac/dc power supply
SPECIFICHE TECNICHE
Technology
Tuning
Detection mode
Presence time
Pulse time output
Inductance range
Frequency range
Frequency steps
Sensitivity (DL/L)
Reaction time
Power supply (depending on model)
Mains Frequency
Power Consumption
Storage temperature range
Operating temperature range
Degree of protection
2 Output relays
(free potential change-over contact)
• max contact voltage : 230 Vac
• max contact current : 5A (resistive)
LED indicators
• 1 green LED : power
• 1 red LED : Loop status 1
• 1 red LED : Loop status 2
Protections
• loop insulation transformer
• zener diodes
• gas discharge clamping
Connection
Dimensions
Weight
Product compliance
DESCRIPTION OF THE SENSOR
Power LED
Dip Switches
Detection state LED
(only with dual loop)
Detection state LED
Dual Loop Con guration A
Loop A
Loop B
ment
Relay A
oop)
Pulse on entry B
Relay B
ment
(non-directional mode)
Pulse on entry A
Pulse on entry B
Relay B
(directional A— B mode)
Pulse on entry A
EN
Dual Loop Con guration B
p B
inductive loop
automatic
presence
1 min to infinity (permanent
presence) with 250 steps
100 ms or 500 ms
20 mH to 1000 mH
20 kHz to 130 kHz
4 for single loop
2 for dual loop (for each loop)
0.005% to 0.5% with 250 steps
25 ms for single loop
50 ms for dual loop (each channel)
12-24 ac/dc ±10%
230 Vac ±10%
90 -----> 125 Vac ±0%
48 to 62 Hz
< 2.5 W
–30°C to +70°C
–30°C to +40°C
IP40
Power LED
Dip Switches
Detection state LED
standard 11-pin round
(only with dual loop)
connector 86CP11
Detection state LED
77mm (H) x 40mm (W) x 75mm (D)
< 200gr
R&TTE 1999/5/EC
EMC 2004/108/EC
UL listed equipment for UL 508
Dual Loop Con guration A
Loop A
Loop B
Relay A
Presence time
Pulse on entry B
adjustment
Relay B
(non-directional mode) Sensitivity adjustment
Pulse on entry A
potentiometer
(only with dual loop)
Pulse on entry B
Sensitivity adjustment
Relay B
potentiometer
(directional A— B mode)
Pulse on entry A
Dual Loop Con guration B
Loop A Loop B
Main connector
(86CP11)
Pulse on exit B
(non-directional mode)
Pulse on exit A
Pulse on exit B
(directional A— B mode)
Pulse on exit A
Loop A Loop B
LOOPS INSTALLATION TIPS
A. CABLE SPECIFICATIONS FOR LOOP AND FEEDER
• 1.5mm cross section area
2
• Multi-strand cable
• Insulation material : PVC or Silicone
• For the feeder cable, the wire must be twisted at least 15 times by meter
• Feeder for long runs used for foil screened cable is recommended (earth
at equipment end only)
• The feeder cable must be firmly fixed to avoid any false detection (max
length : 100 m)
• Waterproof cable junction box is required
B. LOOP GEOMETRY
Ea
Eb
• With two adjacent loops connected to a dual channel sensor, it is possible
for these loops to share a common slot, if so required.
As the channels are multiplexed, no interference will occur
• Avoid large loops or long feeder (max 100 m), the sensitivity will be af-
Spira doppia - con gurazione A fected
Dip Switches
Frequency adjustment for loop A for single loop detector
Spira A
Dip Switch #1
Spira B
off
Detection state LED
(only with dual loop)
Relè A
on
Detection state LED
off
Relè B
on
(modo non direzionale)
Dual Loop Con guration A
Relè B
(modo direzionale A— B)
Presence time
adjustment
Sensitivity adjustment
potentiometer
(non-directional mode)
(only with dual loop)
Sensitivity adjustment
potentiometer
(directional A— B mode)
Dual Loop Con guration B
Loop A Loop B
Main connector
Pulse on exit B
(86CP11)
(non-directional mode)
Pulse on exit A
Pulse on exit B
(directional A— B mode)
Pulse on exit A
Loop A Loop B
Loop A
Loop B
Relay A
Pulse on entry B Pulse on exit B
Relay B
Pulse on entry A Pulse on exit A
Pulse on entry B Pulse on exit B
Relay B
Pulse on entry A Pulse on exit A
L
feeder
Cavo di
cable
collegamento
Power LED
Spira A Spira B
Dip Switch #2
off High
off Mid High [High –20%]
Impulso sulla spira B - Impulso sulla spira B -
ingresso uscita
on Mid Low [High – 25%]
on Low [High – 30%]
Impulso sulla spira A - Impulso sulla spira A -
ingresso uscita
Impulso sulla spira B - Impulso sulla spira B -
ingresso uscita
Impulso sulla spira A Impulso sulla spira A -
Loop A
ingresso uscita
Loop B
Main connector
(86CP11)
Relay A
Pulse on entry B Pulse on exit B
Relay B
Pulse on entry A Pulse on exit A
Pulse on entry B Pulse on exit B
Relay B
Pulse on entry A Pulse on exit A
Loop A
Loop B
Relay A
Pulse on entry B Pulse on exit B
Relay B
Pulse on entry A Pulse on exit A
Pulse on entry B Pulse on exit B
Relay B
Pulse on entry A Pulse on exit A
Presence time
adjustment
Spira doppia - con
Sensitivity adjustment
Spira A
Loop frequency potentiometer
(only with dual loop)
Spira B
Sensitivity adjustment
Relè A
potentiometer
Relè B
(modo non direzionale)
Dual Loo
Loop A Loop B
Relè B
(modo direzionale A— B)
(non-directi
(directional A—
Loop A Loop B
3