Vimar Elvox TAB 7509 Instrucciones Instalador página 12

Ocultar thumbs Ver también para Elvox TAB 7509:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 26
TAB: 7509
Configurations
Selecting call tunes
10 different ringtones can be selected. It is also possible to distinguish
between external calls, intercom calls and landing calls (see the case
described below). The melodies are selected with the entryphone/video
entryphone on stand-by and the handset on the hook.
- Push button
is used to enter configuration mode.
- Key is used to select the ENTRANCE PANEL CALL melody.
- Key
is used to select the INTERCOM CALL melody.
- Key
is used to select the LANDING CALL melody (exclusively using
the push button interfacing module Art. 6120 or Vimar landing call but-
ton). For landing calls using a push button connected directly to the
terminals FP and M on the entryphone, the ringtone cannot be changed.
Configuration:
1) Press key
and hold it down (for 2 s), until LED
and the entryphone emits an audible signal.
2) press and hold the chosen ringtone key (key /key /key ) until you
hear the melody on the entryphone.
3) press the key (key /key
/key
melody.
4) Having chosen the desired ringtone, press key
not touch any keys for 5 s. After completing the configuration, the LED
flashes and then turns off.
Ringtone volume adjustment
The ringtone volume is adjustable with 6 levels.
The ringtone volume must be adjusted with the entryphone/video entryph-
one on stand-by and the handset on the hook.
Configuration:
1) Press key
and hold down (for 2 s) until the LED
and the entryphone emits an audible signal.
3) Press key
to reduce,
keys are pressed the volume changes by one level.
4) Once you have selected the desired volume, press key
or do not touch any keys for 5 s. After completing the configuration, the
flashing LED goes off and a "beep" is emitted.
Ringtone muting
To mute the ringtone, press key
is confirmed with a "low-pitched" tone and the key
steady light. The ringtone reactivation is signalled by a "high-pitched" tone
and key
going off. The indoor station can keep up to 4 unanswered
calls in the memory, indicated by
sists of one flash per missed call. When the ringtone is restored the coun-
ter is reset. This function can be activated with the indoor station at rest.
12
starts flashing
) repeatedly to select the desired
to store it or do
starts flashing
to increase the volume. Each time the
to store it
and hold down (for 2 s). Deactivation
lighting up with a
LED flashing. Saving to memory con-
Operation
Important: for the entryphone to work, the ID must have already been
programmed. To check this, press a key on the entryphone: if an ID has
been assigned to the entryphone, a beep will sound when a push button
is pressed; if no ID has been assigned or it has been deleted, a triple
beep will sound.
Answering a call
A call from the entrance panel or from an intercom device can be answered
during the ringtone cycle or once it has ended. To answer, lift the handset;
to end the call, replace the handset.
Receiving a door call
The entryphone can receive calls from a landing call button if connected to
terminals M and FP directly or via interface Art. 6120 (see wiring versions).
When the landing call button is pressed, the entryphone rings with a differ-
ent tone from those generated by calls from the entrance panel or intercom
calls. To stop the ringtone, lift the handset.
For landing calls using the push button connected directly to terminals FP
and M on the entryphone, the ringtone cycle duration depends on how long
the push button is pressed, for a maximum of 10 s. In this case the melody
cannot be configured.
Making an intercom call
To make a call to another indoor station, one or more push buttons must
have been programmed (see paragraph on "Push button programming").
To call, lift the handset and press the push button programmed and re-
ferring to the indoor station to call. During the call, the entryphone emits
a tone in order to signal that the call is underway, or if the entryphone/
video entryphone is already busy in another call, a tone will be heard on
the entryphone/video entryphone making the call to indicate that the user
called is busy.
When the called party answers, the communication is automatically acti-
vated. Hang up the handset to end the conversation.
The maximum conversation time is 5 minutes (by default).
Missed call
The LED
(Ringtone muted) remains on and goes off briefly 1, 2, 3 up
to 4 times for each cycle according to the number of calls received but
not answered for any reason. Before answering the LED
muted) stops flashing if it was previously flashing due to a any previous
missed calls. Answering the current call also causes the flashing to stop
once the indoor station returns to stand-by. It stops flashing also when
running a self-start.
Muting the ringtone during a call
When receiving a call from an entrance panel, an intercom device or a
landing call via device Art. 6120, the call ringtone can be muted by press-
ing key
.
Lock command
Press the lock push button (with the handset on the hook or in conversation
mode) to send a lock opening command to the entrance panel (by default,
the last entrance panel to make a call).
Self-start
-
Self-start with specific key (key
nicate with the master panel, lift the handset and press the key briefly
per attivare la comunicazione. Replace the handset to end the
conversation.
-
Self-start with programmed key to a specific panel: to run the self-
start and communicate with a specific panel, lift the handset and press
the key programmed to call the specific panel (see paragraph on "Pro-
EN
(Ringtone
): to run self-start and commu-

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Elvox tab 7509/d

Tabla de contenido