Quick Setup; System Setup; Dvd Setup - Denon ADV-700 Manual De Instrucciones

* This section describes surround-related setup operations.
For DVD-related setup operations, see page 40,
• The setup operations cannot be performed while discs are playing, Set the stop mode first.
2
m 5
Refer to "CONNECTIONS" (pages 5 to 8) and check
that all connections are correct.
2
Turn on the power.
Press the POWER switch (button).
ON / STANDBY
Light
en)-i_
Main unit Remote control unit
When pressed, the power turns on and the display lights. The
sound is muted for several seconds, after which the unit
operates normally. When pressed again, the power turns off,
the standby mode is set and the display turns off.
Whenever the ON/STANDBY button is in the STANDBY state,
the apparatus is still connected on AC line voltage. Please be
sure to unplug the cord when you leave home for, say, a
vacation.
Press the SETUP button, s_Jp
DENON
I_A0YANCED SETU_>]
I >EXI
Remote control
unit
Use the A and V cursor buttons
on the remote control unit to select
the setting menu.
• There are three types of setup
menus.
Remote control unit
@ QUICK SETUP: To switch between the 2- and 5,1-channel
modes
@ SYSTEM SETUP: Detailed settings of the AV system
function
@ DVD SETUP: Detailed settings of the DVD function
Press the ENTER button to display
the setting screen of the respective
menu.
• The ADV-700 is preset with Quick System settings for a 5.1-channel surround system using five small speakers and a
subwoofer or a 2-channel virtual system using two large front speakers with or without a subwoofer,
• The system settings can be made and the ADV-70O used for playing discs simply by choosing the speaker systems you are using.
See "(4) System setting changes" (pages 14 to 16 when using speaker systems other than the ones described below or if you
wish to change the settings.
At the setup screen, select "QUICK SETUP", then press
the ENTER button. (See page 13,)
At the quick system setting screen,
use the A and V cursor buttons
to select the speaker system you are
using.
• The selected speaker name is indicated in
yellow.
• The setting is displayed.
Remote control
unit
{ L_dl_ _ LfP M;ENU d DENON
LSELECT YOUR SPEAKER SYSTEM
............................. I
I S.ICHSURROUN
I 2,CII V H_TU ]
I Z'Ct{ WI_TUAL_SW
kS_TUP _ALgI_S>
I F_I[I_J _AU. 2,_Sl
I ALL2.4ml
I
J J}EC I_SlON _ F-NT_B_N I
Press the ENTER button to enter the
setting,
• The setup screen reappears,
Remote control unit
4
Press the SETUP button to quit the
setup mode.
You can also quit the setup mode
by using the V cursor button at
the setup screen to display "Quit
setup" in yellow then pressing
the ENTER button,
Remote control
unit
To change the settings
At the setup screen, select "SYSTEM SETUP" from
"<ADVANCED S ETU P>",
Quick system setting parameters
5.1-channel surround system
Low frequency Delay time
playback ability (distance)
Front : Small 2,7 m (9 ft.): L2
Center : Small 2,4 m (8 ft.): L1
Surround : Small 2,1 m (7 ft.): L3
Subwoofer : Yes 2,7 m (9 ft.): L2
L3 L3
Surround L
2-channel virtual system
Front : Large (2 channels only)
2-channel virtual + subwoofer system
Front : Large
Placed at equal distances
Subwoofer : Yes
Front L
Subwoofer
Listening
position
Remote control unit
13