Denon ADV-700 Manual De Instrucciones página 24

• In the auto decode mode, it is possible to play signals in the Dolby Digital, Dolby Pro Logic i1 or DTS, according to the format of
the input signals,
• It is also possible to play 2-channel sources according to the 2-channel decode mode and Dolby Pro Logic 11mode settings (page
23) and in the Dolby Pro Logic 11Surround mode,
[1] Dolby Digital and DTS playback (digital inputs only)
• Applicable sources
• Digital inputs (TV/DBS and MAUX functions, including DVD
playback discs)
Dolby Digital multi-channel sources
DTS sources
Set the surround mode to "AUTO DECODE".
SURROUND FUNCTION
SURROUNU
MODE /SELECT
Main unit Main unit Remote control unit
I/oog)_
2
o@G
_®_®
/.3
--3
--1
--6
m 5
When performing this operation from the main unit,
press the SURROUND MODE button then turn the
FUNCTION/SELECT dial to choose the surround
mode.
Play a program source containing the L_]l Q i T[_]A L or
[J'_L_ mark.
• The Dolby Digital indicator
lights when playing a nnDIGITAL _,RT- Lit
Dolby Digital source.
• The DTS indicator lights .BTS. _- Lit
when playing a DTS
source.
The mode is selected automatically according to the
format of the source being played.
5
Display the surround parameters SUltAnA
for the source. "_-(_
The surround parameters are
also displayed on the screen
when the function is set to
DVD. Remote control unit
Select the digital input function. (DVD or TV/DBS or
u
MAUX digital input)
FUNCTION
/SELECT
Main unit
Set the input mode to
"AUTO".
DTS sources can also be
played in the input mode
"DTS'.
Remote control unit
Remote control unit
Select the various surround
parameters and set them.
The display returns to
normal if no operation is
performed for 4 seconds
while the parameters are
displayed.
• D.COMR setting
Remote control unit
I t::;_.C.,.::.V_iF"_ Of::F_ I
G
This parameter is not displayed when playing DTS
source.
6
• LFE level setting
The LFE level can be adjusted between -10 dB and
0 dB in steps of 1 dB.
• DEFAULT setting
I '--."',"I
When "YES" is selected, the settings are reset to
their factory default values.
Stop operating buttons once the surround parameter
settings have been completed. After several
seconds the normal display reappears and the
settings are automatically set.
NOTES:
• When "DEFAULT" is selected and the _ cursor button
is pressed ("YES"), "D.COMR" is automatically set to
"OFF" and "LFE" is reset to the default value.
("D.COMR" is not valid for DTS source.)
• Signals encoded in Dolby Digital can only be played in
the Auto decode (Dolby Digital, Dolby Pro Logic i! or
Auto stereo), Direct, stereo or virtual modes, Other
modes do not work when playing Dolby Digital signals.
• DTS signals can only be played in the Auto decode
(DTS), Direct or stereo modes, Other modes do not
work when playing DTS signals.
• DTS signals can also be played in the "DTS" input
mode. (See page 19.) In this case, decoding and
playback are only performed when DTS signals are
input,
Surround parameters (3)
D.COMR (Dynamic Range Compression):
• Motion picture soundtracks have tremendous
dynamic range (the contrast between very soft and
very loud sounds). For listening late at night, or
whenever the maximum sound level is lower than
usual, the Dynamic Range Compression allows you to
hear all of the sounds in the soundtrack (but with
reduced dynamic range). (This only works when
playing program sources recorded in Dolby Digital.)
Select one of the four parameters ("OFF", "LOW",
"MID" (middle) or "HI" (high)). Set to OFF for normal
listening.
LFE (Low Frequency Effect):
• Program source and adjustment range
1. Dolby Digital: -10 dB to 0 dB
2. DTS Surround: -10 dB to 0 dB
• When Dolby Digital encoded software is played, it is
recommended that the LFE LEVEL be set to 0 dB for
correct Dolby Digital playback.
• When DTS encoded movie software is played, it is
recommended that the LFE LEVEL be set to 0 dB for
correct DTS playback.
• When DTS encoded music software is played, it is
recommended that the LFE LEVEL be set to -10 dB
for correct DTS playback.
24