Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Ford Focus 2008-2011
KIT FEATURES
• DIN radio provision with pocket
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• Painted to match factory dash
KIT COMPONENTS
• A) Radio housing trim panel • B) ISO brackets • C) ISO trim plate • D) ISO DDIN brackets
• E) ISO DDIN trim plate • F) Pocket • G) (2) Top clips • H) (4) Middle radio housing clips
A
B
C
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • XSVI-5520-NAV • XSVI-5521-NAV • AX-ADBOX2 & AX-ADFD01
Antenna Adapter: • Not required
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver • Socket set • Cutting tool • T-20 Torx driver
METRA. The World's best kits.
Installation instructions for part 99-5816
99-5816
D
E
™
metraonline.com
Dash Disassembly ..............................................2-3
Kit Preparation ....................................................... 4
- DIN radio provision with pocket ............................ 5
-
-
F
G
H
CAUTION!
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con -
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
Table of Contents
ISO DIN radio provision with pocket ...................... 6
ISO DDIN radio provision ...................................... 7
Metra recommends disconnecting the negative bat -
© COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
Publicidad
Tabla de contenido
Manuales relacionados para Metra 99-5816
Resumen de contenidos para Metra 99-5816
-
Página 1: Tabla De Contenido
• E) ISO DDIN trim plate • F) Pocket • G) (2) Top clips • H) (4) Middle radio housing clips CAUTION! Metra recommends disconnecting the negative bat - tery terminal before beginning any installation, unless the vehicle manufacturer recommends against so. Please check with your local WIRING &... -
Página 2: Dash Disassembly
99-5816 Dash Disassembly 1. Unclip and remove the trim panel surrounding the shifter, including the cup holders. (Figure A) 2. Remove (2) 9/32” screws from the bottom edge of the factory radio trim panel. (Figure B) 3. Remove (2) 9/32” screws above the gauge cluster (facing up), then unclip and remove the trim panel surrounding the gauge cluster. - Página 3 99-5816 Dash Disassembly 5. Unclip and remove the vent panel 9. Remove (4) T-20 Torx screws at the top of the factory radio trim securing the accessory socket panel. (Figure E) panel to the factory radio trim panel assembly and remove the 6.
-
Página 4: Kit Preparation
99-5816 Kit Preparation 1. Secure the climate control into the radio housing using the factory hardware. (Figure A) 2. Secure the accessory socket panel to the radio housing using the factory hardware. (Figure B) 3. Clip the passenger air bag light and the switch panel blank plates into the radio housing. -
Página 5: Kit Assembly
Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the radio for proper operation. 6. Reassemble the dash in reverse order of disassembly. -
Página 6: Iso Din Radio Provision With Pocket
(Figure C) Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio and climate controls. Metra recommends using the proper mating adapter from Metra or AXXESS. Re- connect the negative battery terminal and test the radio for proper operation. -
Página 7: Iso Ddin Radio Provision
4. Snap the ISO DDIN trim plate onto the front of the radio housing trim panel. (Figure C) 5. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the radio for proper operation. -
Página 8: Important
Installation instructions for part 99-5816 IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. -
Página 9: Características Del Kit
Instrucciones de instalación para la pieza 99-5816 Indice Ford Focus 2008-2011 99-5816 Desmontaje Dash ..........2-3 Preparación del kit ..........4 CARACTERÍSTICAS DEL KIT Ensamble del kit • Provisión de radio DIN con cavidad – Provisión de radio DIN con cavidad ...... 5 •... - Página 10 99-5816 Desmontaje Dash 1. Desenganche y quite la palanca de cambios, incluyendo las rejillas del aire acondicionado. (Figura A) 2. Retire (2) 9/32” tornillos del borde inferior del panel de ajuste de radio de fábrica. (Figura B) 3. Retire (2) 9/32” tornillos por encima del conjunto de indicadores (hacia arriba), después soltar y retirar el panel de ajuste que...
- Página 11 99-5816 Desmontaje Dash 5. Desenganche y quite el panel de 8. Quite los (4) tornillos Torx T-20 que sujetan los controles del clima al las rejillas que están en la parte conjunto del panel de la moldura superior del panel de la moldura del radio de fábrica y quite los...
-
Página 12: Preparación Del Kit
99-5816 Preparación del kit 1. Sujete el control de clima a la carcasa del radio usando la tornillería de fábrica. (Figura A) 2. Sujete el panel del enchufe de accesorios a la carcasa del radio usando la tornillería de fábrica. (Figura B) 3. -
Página 13: Ensamble Del Kit
Metra recomienda que use adaptadores adecuados de acoplamiento de Metra y/o de AXXESS. Vuelva a conectar la terminal negativa de la batería y pruebe el radio para verificar que funcione correctamente . - Página 14 Metra recomienda que use adaptadores adecuados de acoplamiento de Metra y/o de AXXESS. Vuelva a conectar la terminal negativa de la batería y pruebe el radio para verificar que funcione correctamente .
- Página 15 DDIN en el borde interior del panel de todas las conexiones necesarias la moldura de la carcasa del radio. al radio. Metra recomienda que (Figura B) use adaptadores adecuados de acoplamiento de Metra y/o de 3.
-
Página 16: Importante
Instrucciones de instalación para la pieza 99-5816 IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente...