TFA 35.1106 Instrucciones Para El Manejo página 11

TFA_No. 35.1106 Anleitung_11_12
PURE PLUS – Wireless weather station
• Press MEM button again and the highest outdoor (CH 1, 2 or 3) and indoor temperature and
humidity is displayed since the last reset.
• MAX appears on the display.
• Press MEM button again and you will return to normal mode.
• Press and hold MEM button (approx. 5 sec.) in MAX/MIN-mode to clear the recorded MAX/MIN
readings.
• The display shows the current temperature and humidity.
7.2.2 Temperature display
• Press and hold MODE button in temperature and humidity mode
• Press MODE button to change between °C (Celsius) or °F (Fahrenheit) as temperature unit.
7.2.3 Trend pointers
• The trend pointers displayed on the LCD indicate if the temperature and humidity values are
increasing, steady or decreasing.
7.2.4 Outdoor temperature alarm
• Press ALARM button in temperature - humidity mode to enter the temperature alarm function.
• and OFF or the last adjusted upper temperature limit is indicated.
• Press and hold ALARM button for 3 seconds to enter the setting mode.
• The temperature indication flashes.
• Press ▲ or ▼ button to adjust the upper temperature limit.
• Confirm with ALARM button.
• Press ALARM button twice to get to the lower temperature limit.
• and OFF or the last adjusted lower temperature limit is indicated.
• Press ALARM button for 2 seconds to enter the setting mode.
• The temperature indication flashes.
• Press ▲ or ▼ button to adjust the lower temperature limit.
• Confirm with ALARM button.
• Once the temperature alarm starts to ring,
press ALARM button.
• The alarm setting is always valid for all connected transmitters (CH 1, 2 and 3).
7.2.5 Comfort level
• For the indication of the comfort zone of the indoor climate on the display appears:
Display Measuring range
Temperature
COMFORT 20°C ... 25°C
(68°F ... 77°F)
WET -5°C ... +50°C
(+23°F ... +122°F)
DRY -5°C ... +50°C
(+23°F ... +122°F)
20
14.11.2012 9:35 Uhr Seite 11
or is flashing. To turn off the alarm function,
Measuring range
Humidity
40%RH ... 70%RH IDEAL
> 70%RH TOO WET
< 40%RH TOO DRY
PURE PLUS – Wireless weather station
7.3 Atmospheric pressure mode
• Press the ▲ or ▼ button to enter the respective display area. When changing the display area a
short beep will sound.
• PRESSURE flashes on the display.
• You are now in atmospheric pressure mode.
7.3.1 Absolute and relative atmospheric pressure
• Press MODE button to select between the relative (SEA LEVEL) or absolute (LOCAL) pressure and
the selected local altitude (meter/feet)
• Absolute pressure is the actual atmospheric pressure measured by the main unit.
• Relative pressure is referred to sea level's pressure and has to be adjusted first to your local altitude.
• You can set the relative atmospheric pressure directly (recommended) or via the local altitude.
7.3.2 Setting of the relative atmospheric pressure (recommended)
• Ask for the present atmospheric pressure of your home area (Local weather service, www, optician,
calibrated instruments in public buildings, airport).
• Press MODE button in atmospheric pressure mode until SEA LEVEL appears.
• Press and hold MODE button and the atmospheric pressure display starts flashing. Press ▲ or ▼
button to adjust the desired value.
• Confirm with MODE button.
7.3.3 Setting of local altitude (only if the relative atmospheric pressure was not directly set)
7.3.3.1 Setting of local altitude during set-up
• After batteries were inserted, hPa/mbar flashes on the display for 60 seconds.
• Press ▲ or ▼ button to select the measuring unit hPa/mbar, inHG or mmHG for the atmospheric
pressure.
• Confirm with MODE button.
• Meter flashes on the display.
• Press ▲ or ▼ button to select between Meter or Feet as measuring unit.
• Confirm with MODE button.
• The altitude starts flashing. Press ▲ or ▼ button to adjust the desired local attitude (in steps of 1
meter/ 3 feet). Hold ▲ or ▼ button, you will enter fast mode.
• Confirm with MODE button.
• The relative atmospheric pressure will be calculated.
7.3.3.2 Setting of local altitude during normal operation
• Press MODE button in atmospheric pressure mode until the local altitude appears.
• Press and hold MODE button and the altitude starts flashing. Press ▲ or ▼ button to adjust the
desired local attitude (in steps of 1 meter/3 feet). Hold ▲ or ▼ button, you will enter fast mode.
• Confirm with MODE button.
• Press MODE button again to return to normal mode.
• SEA LEVEL appears.
7.3.4 Conversion of the measuring units
• Press MODE button in atmospheric pressure mode until SEA LEVEL appears.
• Press and hold MEM button. hPa/mBar is flashing.
• Press ▲ or ▼ button to select the measuring unit hPa/mBar, inHG or mmHG for the atmospheric
pressure.
21