Phase Switching; Graphic Equalizer Adjustments; Parametric Equalizer Adjustments - Alpine IVA-D100 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Phase Switching

1
Make sure that the defeat is turned off (page 25).
2
Press SETUP.
The SETUP selection screen is displayed.
3
Touch [
] of i-Personalize.
The i-Personalize screen appears.
4
Touch [
] of A.PROCESSOR.
The A.PROC list screen is displayed.
5
Touch [
] of PHASE.
The PHASE adjustment screen appears.
6
Switch the phase (0° or 180°) by touching [ ] or [ ]
of the desired speaker.
7
Touch [RTN] to return to the previous screen.

Graphic Equalizer Adjustments

The graphic equalizer allows you to modify the sound using 31 bands
each for the front (left and right), rear (left and right) and center
speakers. An additional 10 bands are available for the subwoofer. This
allows you to customize the sound to suit your taste.
1
Check that the Defeat mode is off.
2
Press SETUP.
The SETUP selection screen appears.
3
Touch [
] of i-Personalize.
The i-Personalize screen will appear.
4
Touch [
] of A.PROCESSOR.
The A.PROC list screen appears.
5
Select L/R or L+R by touching [ ] or [ ] of G-EQ.
L/R:
Different adjustment values can be set for the left and
right channels.
L+R: Sets the same adjustment values for the left and right
channels.
When parametric EQ is adjusted, this setting will be turned
off.
6
Touch [
] of G-EQ.
The G-EQ list screen appears.
7
Touch [
] of the desired speaker (channel).
The G-EQ adjustment screen appears.
8
Adjust the G-EQ to your preference.
Adjusting the Level
Touch [ ] or [ ] of the desired frequency to adjust the
level.
9
Touch [RTN] to return to the previous screen.
• When the speaker is set to the "OFF" mode, the graphic equalizer
for that speaker cannot be set. Refer to "Setting the Speakers"
(page 41).
• Check the playable frequency ranges of the connected speakers
before making the equalizer adjustments. If the speaker's playable
frequency range is 55 Hz to 30 kHz, for example, adjusting the 40 Hz
or 20 Hz band has no effect. Additionally, you may overload and
damage the speakers.
• When graphic EQ is adjusted, the adjustment for parametric EQ
becomes ineffective.

Parametric Equalizer Adjustments

The frequency bands of the graphic equalizer are fixed. This makes it
very difficult to correct for undesired peaks and dips at specific
frequencies. The parametric equalizer's center frequency can be tuned
to these specific frequencies. Then, the bandwidth (Q) and level are
fine-tuned, independently, to make the necessary corrections. The
parametric equalizer function is an advanced tool for serious
audiophiles.
1
Check that Defeat mode is off.
2
Press SETUP.
The SETUP selection screen appears.
3
Touch [
] of i-Personalize.
The i-Personalize screen will appear.
4
Touch [
] of A.PROCESSOR.
The A.PROC list screen appears.
5
Select L/R or L+R by touching [ ] or [ ] of P-EQ.
L/R:
Different adjustment values can be set for the left and
right channels.
L+R: Sets the same adjustment values for the left and right
channels.
When graphic EQ is adjusted, this setting will be turned off.
6
Touch [
] of P-EQ.
The P-EQ list screen appears.
7
Touch [
] of the desired speaker (channel).
The P-EQ adjustment screen appears.
8
Adjust the P-EQ to your preference.
Selecting the Band
Touch [ ] or [ ] of BAND.
Select the desired band.
Adjusting the Frequency
Touch [ ] or [ ] of FREQ., then adjust the frequency of
the selected band.
Adjusting the Level
Touch [ ] or [ ] of LEVEL, then adjust the level of the
selected band.
43
-EN

Publicidad

Tabla de contenido
loading

Tabla de contenido