Environmental Considerations; If Something Does Not Work - Teka IR 9530 Instrucciones Para La Instalación Y Recomendaciones De Uso Y Mantenimiento

fig. 4
Using the scraper
Blade protected Blade unprotected
A pot or pan may become stuck
to the glass due to a product having
melted between them. Do not try to
lift the pot while the heating zone is
cold! This could break the glass.
Do not step on the glass or
lean on it as it could break and cau-
se injury. Do not use the glass as a
surface for placing objects.
TEKA INDUSTRIAL S.A. reserves the
right to make changes to its manuals
that it deems necessary or useful,
without affecting the product's essen-
tial features.
Environmental
considerations
The symbol on the product
or its packaging means that this
pro duct cannot be treated like or-
dinary household waste. This pro-
duct must be taken to a recycling
collection point for electrical and
electronic appliances. By ensuring
that this product is disposed of
correctly, you will avoid harming
the environment and public health,
which could happen if this pro-
duct is not handled properly. For
more detailed information about
recycling this product, please con-
tact your local authority, household
waste service or the store where
you pur chased the product.
The packaging materials used are
environmentallyfriendly and can be
recycled completely. Plastic compo
nents are marked >PE<, >LD<,
>EPS<, etc. Dispose of packaging
materials, like household waste, in
your local container.
Fulfillment with Energy Efficiency
of the appliance:
-Appliance has been tested accor-
ding to standart EN 60350-2 and the
obtained value, in Wh/Kg, is availa-
ble in the appliance's rating plate.
If something does not
work
Before calling the technical service,
perform the verifications described
below.
The appliance does not work:
Ensure that the power cable is plug-
ged in.
The induction zones do not pro-
duce heat:
The container is not appropriate (it
does not have a ferromagnetic bottom
or is too small). Check that the bottom
of the container attracts a magnet, or
use a larger container.
A humming is heard when starting
to cook in the induction zones:
With containers which are not very
thick or not of one piece, the humming
results from the transmission of energy
directly to the bottom of the container.
The humming is not a defect, but if
you wish to avoid it anyway, reduce
the power level slightly or use a con-
tainer with a thicker bottom, and/or of
one piece.
The touch control does not light
up or, despite lighting, does not
respond:
No heating zone has been selected.
Be sure to select a heating zone befo-
re operating it.There is humidity on the
sensors, and/or your fingers are wet.
Keep the touch control surface and/
or your fingers clean and dry. The
locking function is activated. Unlock
the controls.
The sound of a fan is heard while
cooking, which continues even
after cooking has ended:
The induction zones have a fan to
keep the electronics cool. This only
operates when the electronic circuits
get hot. It stops again when the cir-
cuits cool whether the hob is turned
on or not.
When frying or cooking stew, it
seems as though the energy of the
induction zones decreases ("the
induction element heats less").
If the temperature of the glass or of
the electronic system becomes too
high while cooking, an auto-protection
system will begin working which
regulates the power of the heating
elements so that the temperature
does not continue increasing. Excess
temperature problems during cooking
only occur in extreme situations (an
extended period of time coo king at
maximum power) or when ins tallation
is inadequate. Verify that installation
has been done in accordance with the
indications in the instructions manual.
The hotplate will switch off and the
message C81 or C82 will appear on
the indicators:
Excessive temperature in the electro-
nics or on the glass. Wait for a while
for the electronics to cool down or
remove the pot or pan so that the
glass can cool.
The hob suddenly starts to bleep.
There is a cloth, container or liquid on
the Touch Control. Remove any object
covering the Touch Control and/or
clean any liquid that might have been
spilt on it. The timer was activated and
the preset time has finished. Touch the
clock sensor to deactivate the bleep.
The hob (or any of the hotplates)
powers off during cooking.
There is a container, cloth or liquid
covering the Touch Control. Remove
any object that might be covering the
Touch Control. One or several of the
hotplates has overheated. Allow the
overheated hotplates to cool down for
a few minutes before powering them
up again.
A timed hotplate failed to power off
at the end of the set time.
The hotplate had not been set cor-
rectly. Make sure that the time was
set following the instructions manual.
When cooking at a level below 9,
there are fluctuations in the power.
The induction generator of the cooker
turns on and off alternately in order to
keep the chosen cooking level. This
is not a defect.
The symbol will appear
power indicator of a hotplate:
The induction system does not find a
pot or pan on a hotplate or it is of an
unsuited type.
EN
on the
25