Power Function; Safety Shut Off - Teka IR 9530 Instrucciones Para La Instalación Y Recomendaciones De Uso Y Mantenimiento

on pause. The timer will also be pau-
sed if it is activated.
Activating the Stop function
Touch the Stop sensor
second. The pilot (11) lights up and the
power indicators will show the symbol
to indicate cooking has been
paused.
Deactivating the Stop function
Touch Stop sensor (7) again. The
pilot (11) turns off and cooking resu-
mes under the same power and timer
settings that were established before
the pause.
Heat Sustainment
Function
This function makes it possible to keep
warm food that is in the pan placed on
the cooking area.
This function is independently availa-
ble for each one of the plates.
To activate it, select the plate. The
decimal point will light up. Then push
sensor (13). The symbol "A" will
appear in the indicator and the corres-
ponding pilot (8) will turn on.
To disconnect this function, all you
have to do is modify the power of the
plate or directly turn it off.

Power Function

This function supplies "extra" power
to the plate, above the nominal value.
Said power depends on the size of the
plate, (see values specified with * in
the presentation section), with the pos
sibility of reaching the maximum value
permitted by the generator.
1 Select the desired plate with the
corresponding sensor (3). The deci
mal point will light up.
2 On the cursor Slider, push directly
on position (5). The power level
indicator will show the symbol P,
and the plate will start to supply
extra power.
The Power function has a maximum
duration as specified in table 1. After
this time, the power level will automati-
cally adjust to 9.
(7) for one
Boil Control Function
This innovative function is of an enor-
mous help if you want to cook pasta,
rice, eggs, or boil any kind of food. This
function allows you to perform this co-
oking method "almost" automatically.
This function is available only in the
plates where this symbol appears
Pot requirements
For properly using boil control, the pot
must have the following characteris
tics:
Bottom size as close as possible to the
diameter of the plate.
- NO COVER.
- Filled more than halfway of its capa-
city with room temperature water
(never use lukewarm or hot water).
Not fulfilling these requirements
will result in inadequate control of
boiling.
WARNING: do not use this
function for cooking methods other
than boiling water. Never use oil. It
can overheat and create flames.
Activating the function:
Select the proper plate. The decimal
point lights up.
Push sensor
on the plate indicator and the pilot (9)
will turn on. In the timer for this plate,
a moving segment will appear which
indicates that the system has started
to monitor cooking.
When the system detects that it is
about to boil, an initial beep will go off.
Take this time to prepare the food you
want to boil or cook.
After 30 seconds, a second beep will
go off. If you haven't done it already,
now is time to put the food into the pot.
After the second beep, the system will
activate the timer as a chronometer so
that you can control how long the food
has been boiling.
A few seconds after the chronometer is
activated, a third beep will go off indi-
cating that, from this moment on, the
system will reduce the energy supplied
in order to maintain a gentle and ste-
ady boil. The chronometer will remain
active until cooking has finished.
If desired, the chronometer can be
deactivated and you can set a time for
the countdown to occur and the plate
to automatically turn off (see section
Timer Function).
Deactivating the function
You can cancel the function at any time
.
by simply turning off the plate or modif
ying the power level.
If due to an error one or several
heating zones do not switch off, the
appliance will be automatically discon-
nected after a set amount of time (see
table 1).
(12). An A will appear
When the "safety switch off" function
has been triggered, a 0 is displayed if
the glass surface temperature is not
dangerous for the user or an H if there
is a burn risk.
Keep in mind that this safety function
turns on even when the touch control
is off!
Take precaution and do not place
objects on the touch control!

Safety shut off

Table 1
TEMPO MÁXIMO DE MA-
Selected
XIMUM OPERATING TIME
power level
(in hours)
0
1 8
2 8
3 5
4 4
5 4
6 3
7 2
8 2
9 1
P 10 minutes, readjusts to 9
EN
23