Pan Detector; Stop Function - Teka IR 9530 Instrucciones Para La Instalación Y Recomendaciones De Uso Y Mantenimiento

EN
sliding towards the left decreases it.
It's also possible to directly select a
power level by placing your finger
directly on a desired point of the
cursor slider.
In order to select a plate on these
models, directly touch the POWER
INDICATER NUMBER (3).
TURNING THE APPLIANCE ON
The first time the cooktop is plugged
in (or after a power outage), the Block
function will appear as activated (pilot
light 10 on). In this case, you must
deactivate the block function in order
to turn the cooktop on. To do this, push
sensor (6) until pilot (10) turns off.
1 Touch sensor (1) for at least one
second.
Touch Control is now activated and a 0
appears in all power indicators (3). If a
cooking zone is hot, the corresponding
indicator will show an H and a 0 alter
natively.
Once the Control is on, you must acti
vate a plate within 10 seconds, other-
wise the Touch Control will automati-
cally turn off.
While the touch control is activated, it
can be disconnected at any moment
by touching the general on/off sensor
(1) even if it has been blocked (see
section "Blocking cooktop sensors").
Sensor (1) always has priority in
disconnecting the touch control.
ACTIVATING PLATES
Once the Touch Control is activated
with sensor (1), any plate can be
22
turned on by following these steps:
1 Select the plate by using the corres-
ponding sensor (3). In other words,
press with your finger the NUMBER
INDICATOR. If the glass is hot, the
said indicator will go from showing
an H to showing level 0. The deci-
mal point to the bottom right of the
number lights up, indicating that the
plate has been selected.
2 Use the cursor slider (2) to choose
a cooking level between 0 and 9.
As long as the plate is selected, in
other words, with the decimal point lit
up, its power level can be modified.
TURNING A PLATE OFF
A plate can be turned off by decreasing
its cooking level to 0. In order to do
this, the plate must have been pre-
viously selected (decimal point lit up).
Once a plate has been turned off, an
H will appear on the corresponding
power indicator if the glass surface of
the cooking area reaches an elevated
temperature. Burn risk exists. When
the temperature decreases, the indica
tor turns off (if the cooktop is discon-
nected), or it will show a 0 if it is still on.
TURNING ALL PLATES OFF
All plates can be simultaneously dis-
connected by using the general on/
off sensor (1). All plate indicators
will turn off.

Pan detector

Induction cooking zones have a built-in
pan detector. This way, the plate will
stop working if there is no pan present
or if the pan is not suitable.
The power indicator will show a sym-
bol to designate "there is no pan" if,
while the zone is on, no pan is
detected or the pan is not suitable.
If a pan is taken off the zone while it
is running, the plate will automatically
stop supplying energy and it will show
the symbol for "there is no pan". When
a pan is once again placed on the coo-
king zone, energy supply will resume
at the same power level previously
selected.
The time for pan detection is 3 minu-
tes. If a pan is not placed within this
time period, or the pan is unsuitable,
the cooking zone shuts off. The power
indicator will go from showing the
symbol "there is no pan" to showing 0.
When finished, turn off the cooking
zone by using the touch controls.
Otherwise an undesired operation
could occur if a pan is accidentally
placed on the cooking zone during
the next three minutes. Avoid possible
accidents!
Blocking cooktop
sensors
BLOCK FUNCTION
With the Block Function, you can block
the other sensors, except for the on/off
sensor (1), in order to avoid unde
sired operations. This function is useful
as a childproof safety.
To activate this function, touch sensor
(6) for at least one second. Once
you have done so, the pilot (10) turns
on indicating that the control panel is
blocked. To deactivate the function,
simply touch sensor (6) again.
If the on/off sensor (1) is used to
turn off the appliance while the block
function is activated, it won't be possi-
ble to turn the cooktop on again until
it unblocks.

Stop Function

This function puts the cooking process