Makita DCL142 Manual De Instrucciones página 12

Dust bag and paper pack
Install either dust bag or paper pack before using
cleaner.
Use the dust stopper when installing either dust bag or
paper pack.
Dust bag is usable many times repeatedly by cleaning it
out.
Paper pack is a throw-away type. Throw away the entire
paper pack without emptying when it has become full.
Installing dust bag
Use the dust stopper when installing dust bag. Be careful
not to take the upper side for the lower side by mistake
because they are different each other. (Fig. 11)
1. Insert the protrusion of the dust bag into the groove
in the dust stopper as shown in the figure. (Fig. 12)
2. There is no distinction between the upper and lower
sides of the dust bag. You may insert its protrusion
of any side into the lower groove of the dust stopper.
(Fig. 13)
3. Overlap the frame of dust stopper with that of the
dust bag. (Fig. 14)
4. Place the dust stopper and the dust bag together
into the cleaner cavity in the same direction of arrow
on the dust stopper. Insert them all the way into the
slots in the cleaner cavity. (Fig. 15)
5. Place the entire cloth part of the dust bag inside the
tool itself. (Fig. 16)
6. Close the front cover completely. (Fig. 17)
Installing the paper pack
1. Unfold the entrance of the paper pack before setting
it on the dust stopper. (Fig. 18)
Use the dust stopper also when installing paper pack. Be
careful not to take the upper side for the lower side by
mistake because they are different each other. (Fig. 19)
2. Insert the protrusion of the paper pack into the
groove in the dust stopper as shown in the figure.
(Fig. 20)
3. There is no distinction between the upper and lower
sides of the paper pack. You may insert its protru-
sion of any side into the lower groove of the dust
stopper. (Fig. 21)
4. Overlap the frame of dust stopper with that of the
paper pack. (Fig. 22)
5. Place the dust stopper and the paper pack together
into the cleaner cavity in the same direction of arrow
on the dust stopper. Insert them all the way into the
slots in the cleaner cavity. (Fig. 23)
6. Place the entire container part of the paper pack
inside the tool itself. (Fig. 24)
7. Close the front cover completely.
CAUTION:
• Forgetting to install the dust bag or the paper pack, fail-
ure to insert the dust stopper together with the dust bag
or the paper pack all the way into the slots or using a
broken or ripped bag, may allow dust to get into the
motor. This may result in motor failure.
• Do not fold the cardboard at its opening when installing
the paper pack.
• Never throw away the dust stopper because it need to
be used repeatedly whenever either the dust bag or the
paper pack is used.
12
• The paper pack for the cleaner is an important compo-
nent for maintaining the tool performance. Using other
than the genuine paper pack may cause smokes or
ignition.
OPERATION
CAUTION:
• To connect attachments, such as nozzle, twist-insert
attachment in direction of arrow to ensure secure con-
nection during use. To disconnect attachment, twist-
extract also in direction of arrow. (Fig. 25)
Cleaning (Suction)
Nozzle (Fig. 26)
Attach the nozzle to clean off tables, desks, furniture, etc.
Nozzle slips on easily.
Nozzle + Extension wand (Straight pipe) (Fig. 27)
The extension wand fits in between the nozzle and the
cleaner itself. This arrangement is convenient for
cleaning a floor while standing erect.
Corner nozzle (Fig. 28)
Fit on the corner nozzle for cleaning corners and
crevices of a car or furniture.
Corner nozzle + Extension wand (Straight pipe)
(Fig. 29)
In tight quarters where the cleaner itself cannot squeeze
in, or in high places hard to reach, use this arrangement.
Cleaning without nozzle (Fig. 30)
You can pick up powder and dust without nozzle.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off before
attempting to perform inspection or maintenance.
After use
NOTE:
• Putting the cleaner against the wall without any other
support cause the cleaner to fall down and be dam-
aged. (Fig. 31)
Cleaning
From time to time wipe off the outside (cleaner body) of
the cleaner using a cloth dampened in soapy water.
Clean out also the suction opening, dust bag/paper pack
mounting area and the dust stopper. (Fig. 32)
CAUTION:
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Wash the dust bag in soapy water when it is clogged with
dust and the cleaner power becomes small. Dry it out
thoroughly before use. An insufficiently dried bag may
cause poor suction and shorten the service life of the
motor. (Fig. 33)
NOTE:
• Paper pack is a throw-away type.
When the sponge filter is clogged with dust, remove it
from the cleaner and then wipe it off or wash in water.
Removing and installing the sponge filter (Fig. 34
& 35)
To remove the sponge filter, remove the dust bag or
paper pack and then pinch and take it out.