Hughes & Kettner ATTAX 200 Manual De Instrucciones página 7

ATTAX-MANUAL
GREEN CHORUS LED: Denotes the chorus effect is active in the CLEAN and
CRUNCH channels by flashing at the selected modulation frequency
LEAD SELECTOR SWITCH: Switches back and forth between the
CLEAN/CRUNCH section and the LEAD channel. The LEAD channel is
active when the button is depressed. Once the MSM-1 Module has been
installed, this switching function can be executed via MIDI
RED LEAD LED: The red LED illuminates
when the LEAD channel is active.
MODE 2: Selects either the LEAD 1 or LEAD
2 modes. LEAD 2 is active when the button is
pressed. Once the MSM-1 Module has been
installed, this switching function can be exe-
cuted via MIDI.
LEAD
CHORUS
5 5 0
-5 +5
10 0 10 0 10
E DEPTH LEAD GAIN BASS
EQ SECTION: Active BASS, passive MID
and TREBLE tone controls for the LEAD
channel. Here too, MID and TREBLE influ-
ence each other for the widest possible
range of subtle tonal variations.
LEAD GAIN: Determines the
amount of distortion in the
LEAD channel
DEPTH: Controls the chorus effect's
modulation depth for the CLEAN
and CRUNCH channels.
MAINS: Connect the included Euro-
norm mains cord to this socket.
Ensure the amp's voltage rating
matches your local AC voltage
rating before you plug the cord into
the wall socket.
50 - 60 Hz
Max. power
consumption
480 VA
SPEAKERS LEFT: Two 1/4" output jacks for connecting speakers to
the left channel. The two jacks are wired in parallel. Ensure the
overall impedance does not drop below 4 ohms for these two out-
puts. For the ATTAX 200 combo, you can connect an additional
speaker cabinet (at least 8 ohms/60W) in parallel to the internal
speaker.
For the head version, you can connect one cabinet (at least 4
ohms/120W) or two 8-ohm cabinets.
RED MODE 2 LED: This red LED illumi-
nates when the LEAD 2 mode is active.
MODE 2
0 0 5 5
-5 +5 -5 +5
0 10 0 10
MID TREBLE LEAD MASTER RATE
LEAD MASTER:
Controls the volume
of the LEAD chan-
nel.
HEADPHONES: 1/4" headphone
jack. In order to switch the main
speaker off, unplug the speaker
cable.
MADE IN ST. WENDEL GERMANY
230 V~ CAUTION! HEAD
TO PREVENT THE RISK OF FIRE AND
PHONES
SHOCK HAZARD DON´T EXPOSE
100 V~
THIS APPLIANCE TO MOISTURE OR
RAIN. DO NOT OPEN CASE;
117 V~
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
GREEN CHORUS LED: Denotes
the chorus effect is active in the
LEAD channel by flashing at the
selected modulation frequency
CHORUS SELECTOR SWITCH:
Activates the chorus effect for all
channels.
MASTER
CHORUS FX LOOP
5 5
0 10 0 10 DRY WET
DEPTH REVERB FX MIX
REVERB: Controls how much integrated
reverb is added to the signal. Reverb is
automatically adjusted for each channel
when you switch channels.
DEPTH: Controls the chorus effect's
modulation depth for the CLEAN and
CRUNCH channels
RATE: Controls the chorus effect's modulati-
on rate for the LEAD channel. At a RATE set-
ting of approximately 12 o'clock, the
"Vintage Rotary Effect" kicks in.
RECORDING OUT L/R: These
output jacks can feed a mixing
console or additional (stereo)
power amp.
LEAVE ENOUGH SPACE FOR PROPER VENTILATION!
OUTPUT 120 WATTS OUTPUT 120 WATTS
MIN. IMP. 4 Ohms MIN. IMP. 4 Ohms
SPEAKERS
LEFT RIGHT
SPEAKERS RIGHT: Right
channel speaker output
jacks.
RETURN L/R: If you are using a stereo signal processor, connect these jacks to
the processor's OUTPUT jacks. For mono operation, connect the RETURN L
jack only.
GREEN FX LED: Lights when
the ATTAX 200 FX LOOP is
active.
FX LOOP SELECTOR: Activates the
ATTAX 200 FX LOOP. Once the MSM-
1 Module has been installed, this swit-
ching function can be executed via
MIDI.
5
0 10
MASTER
MASTER: Determines the over-
all output level of the ATTAX
200. The level of the RECOR-
DING OUT signal is unaffec-
ted by the MASTER control.
FX MIX: This control lets you decide how
much of the processed signal is mixed in
with the original signal. Determines the
original signal's volume and its relations-
hip to that of the connected effects devi-
ce's processed signal. DRY = original sig-
nal only, WET = processed signal only
SEND: If you are using a stereo signal proces-
sor, connect these jacks to the processor's
INPUT jacks. For mono operation, connect
only the ATTAX 200's SEND R jack to the
processor's INPUT jack.
TO INSTALL MIDI MODULE:
DISCONNECT AC POWER CORD
BEFORE REMOVING THIS COVER
RECORDING OUT STEREO FX-LOOP
LEFT RIGHT L RETURN R L SEND R
-10 dB
Ser. No.
MONO MONO ATTAX 200
- 10 db SWITCH: This switch allows you to redu-
ce the signal level being sent to external effects
devices. Press this switch for instrument level
processors (e.g. stomp boxes).
MAINS: AC power switch.
MAINS
7