Other Features - mundoclima MUPO-12-H9 Manual De Instalación Y Usuario

Operation
Operation Instructions
COOL operation
-Press the "MODE" button until the "COOL" indicator light
comes on.
-Press the ADJUST buttons "+" or "-" to select your
desired room temperature. The temperature can be set
within a range of 17°C~30°C/62°F~86°F(or 88°F).
-Press the "FAN SPEED" button to choose the fan speed.
HEAT operation(cooling only models without)
-Press the "MODE" button until the "HEAT" indicator
light comes on.
-Press the ADJUST buttons "+" or " - " to select your
desired room temperature. The temperature can be set
within a range of 17°C~30°C/62°F~86°F(or 88°F).
-Press the "FAN SPEED" button to choose the fan speed.
)RU VRPH PRGHOV WKH IDQ VSHHG FDQ QRW EH DGMXVWHG
under HEAT mode.
DRY operation
-Press the "MODE" button until the "DRY" indicator light
comes on.
-Under this mode, you cannot select a fan speed or
DGMXVW WKH WHPSHUDWXUH 7KH IDQ PRWRU RSHUDWHV DW
LOW speed.
-Keep windows and doors closed for the best
dehumidifying effect.
-Do not put the duct to window.
AUTO operation
-When you set the air conditioner in AUTO mode, it will
automatically select cooling, heating(cooling only models
without), or fan only operation depending on what
temperature you have selected and the room
temperature.
-The air conditioner will control room temperature
automatically round the temperature point set by you.
-Under AUTO mode, you can not select the fan speed.
NOTE: Under AUTO mode, both the AUTO mode and the
actual operation mode indicator lights illuminate for some
models.
FAN operation
-Press the "MODE" button until the"FAN " indicator light
comes on.
-Press the "FAN SPEED" button to choose the fan speed.
7KH WHPSHUDWXUH FDQ QRW EH DGMXVWHG
-Do not put the duct to window.
TIMER operation
-When the unit is on, press the Timer button will initiate
the Auto-off stop program, the TIMER OFF indicator light
illuminates. Press the UP or down button to select the
desired time. Press the TIMER button again within 5
seconds, the Auto-on start program is initiated.
And the TIMER ON indicator light illuminates. Press the
up or down button to select the desired Auto-on start time.
-When the unit is off, press the Timer button to initiate
the Auto-on start program, press it again within 5
seconds will initiate the Auto-off stop program.
-Press or hold the UP or DOWN button to change the
Auto time by 0.5 hour increments, up to 10 hours, then
at 1 hour increments up to 24 hours. The control will
count down the time remaining until start.
-The system will automatically revert back to display the
previous temperature setting if there is no operation in
a 5 seconds period.
7XUQLQJ WKH XQLW 21 RU 2)) DW DQ\ WLPH RU DGMXVWLQJ WKH
timer setting to 0.0 will cancel the Auto Start/Stop timer
program.
SLEEP(ECO) operation
-Press this button, the selected temperature will increase
(cooling) or decrease(heating) by 1°C/2°F(or 1°F) 30
minutes. The temperature will then increase (cooling)
or decrease (heating) by another 1°C/2°F(or 1°F) after
an additional 30 minutes. This new temperature will be
maintained for 7 hours before it returns to the originally
selected temperature. This ends the Sleep/Eco mode
and the unit will continue to operate as originally
programmed.
NOTE: This feature is unavailabe under FAN or DRY
mode.

Other features

FOLLOW ME/TEMP SENSING feature(optional)
NOTE:This feature can be activated from the remote
control ONLY. The remote control serves as a remote
thermostat allowing for the precise temperature control
at its location. To activate the Follow Me/Temp Sensing
feature, point the remote control towards the unit and
press the Follow Me/Temp Sensing button. The remote
control will send this signal to the air conditioner until
press the Follow Me/Temp Sensing button again. If the
unit does not receive the Follow Me/Temp Sensing signal
during any 7 minutes interval, the unit will exit the
Follow Me/Temp Sensing mode.
NOTE: This feature is unavailabe under FAN or DRY
mode.
AUTO-RESTART
If the unit breaks off unexpectedly due to the power cut,it
will restart with the previous function setting automatically
when the power resumes.
AIR FLOW DIRECTION ADJUSTMENT
7KH ORXYHU FDQ EH DGMXVWHG DXWRPDWLFDOO\ $GMXVW WKH DLU
flow direction automatically:
-When the Power is ON, the louver opens fully.
-Press the SWING button on the panel or remote
controller to initiate the Auto swing feature. The louver
willl swing up and down automatically.
3OHDVH GR QRW DGMXVW WKH ORXYHU PDQXDOO\
40