Rules For Safe Driving; Replacing The Battery; Assistance Service - Peg-Perego GAUCHO ROCK’IN Empleo Y Manutencion

RULES FOR SAFE DRIVING

For the safety of the child, before starting up the
vehicle read and carefully follow the following
instructions.
• Teach the child how to use the vehicle properly for
safe and enjoyable driving.
• The toy must be used with caution, as it requires
substantial dexterity in order to avoid falls or
collisions which could cause injuries to the user or
third parties.
• Before starting, check that there are no people or
objects obstructing the vehicle's path.
• Drive with hands on the handlebars/steering wheel
and always watch the road ahead.
• Brake in good time to avoid collisions.
ATTENTION! The item is equipped with a brake
system which needs to be appropriately illustrated to
the child by an adult.
2nd GEAR (if present)
Initially, use in 1st gear is recommended. Before
enabling 2nd gear, check that the child has learned to
use the handlebars/steering wheel, 1st gear and the
brake correctly, and has become familiar with the
vehicle.
WARNING!
• Check that all the wheel fixing studs/nuts are
fastened properly.
• If the vehicle is overloaded, as can happen on soft
sand, mud, or very uneven ground, the overload
switch will immediately disconnect the power. The
power supply will be restored after a few seconds.
UNINTERRUPTED FUN: Keep a spare set of charged
batteries ready for use.
PROBLEMS?
THE VEHICLE DOES NOT WORK?
• Check that there are no disconnected cables under
the accelerator plate.
• Check the operation of the accelerator button and
replace it if necessary.
• Check that the battery is connected to the
electrical system.
THE VEHICLE LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by
an assistance centre.

ASSISTANCE SERVICE

PEG PEREGO offers an after-sales assistance
service, directly or through a network of
authorized assistance centres, for any repairs or
replacements and the sale of original spare parts.
To contact a service center, visit our website:
http://global.pegperego.com/toys-
site/support/
The item's serial number must always be quoted.
See the page on spare parts to find out how to
identify the serial number.
Peg Perego always strive to best satisfy their
customers' needs. Knowing the opinions of our
customers is therefore very important and
valuable to us. We would be very grateful if, once
you have used the product, you would fill out the
CONSUMER SATISFACTION QUESTIONNAIRE
which you can find on the internet at:
www.pegperego.com, making any
observations or suggestions you might have.
ASSEMBLY INSTRUCTIONS
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE
VEHICLE FROM ITS PACKAGING. ALL THE
SCREWS AND SMALL PARTS ARE CONTAINED IN
A BAG INSIDE THE PACKAGING. THE BATTERY
MAY ALREADY BE FITTED INSIDE THE ITEM.
ASSEMBLY
1 • Place from bumper on body and tighten four
screws as shown in the drawing.
2 • Place rear bumper on body.
3 • Tighten three screws as shown in the drawing.
4 • Assemble the two parts of the steering wheel.
5 • Place the horn in the steering wheel's central
hole, following the instructions in its packaging.
6 • Insert the steering wheel on the steering wheel
column.
7 • Align steering wheel column holes with steering
wheel: nut fits into haxagon hole, bolt into round
hole.
8 • Insert the windscreen.
9 • Secure it by means of the two screws.
10 • Place seat on body. Adjust seat position. Secure it
with washer and thumb nut.
11 • Join A to part B of the Roll-Bar.
12 • join A-B to the upper section of the Roll-Bar C,
insert and rotate to secure.
13 • Insert the 2 plates in the slots at the base of the
Roll-Bar and hold them in place. Secure the
plates and the Roll-Bar with the 2 screws
provided (detail A).
14 • Insert the end of the safety belt in the slot
situated centrally in the bottom of the seat, as
shown in the figure.
15• Screw the net down to the body.
16 • Snap it around the roll-bar as shown in the
drawing.
17 • Insert the rearview mirrors in the direction
shown by the arrow.
18 • Apply the corresponding stickers to the 2 sides
of the body (see sticker sheet), then press the
two plastic writings into position.
19 • Insert the antenna, pressing down as you do so,
into its appropriate housing, situated on the right
rear mudguard.
20 • Remove the radio from its packaging. Unscrew
the cover from the battery chamber. Insert two
1.5 Volt AA batteries (not supplied with the
vehicle) into the compartment, taking care to
position the positive and negative poles correctly.
Close the battery compartment cover and screw
into place.
21 • Insert the wire from the antenna and the radio
into their appropriate housing on the dashboard,
making sure to place them the right way up, as
shown in the figure.
22 • Snap fit the four hub covers onto the wheels.
23 • Open the bonnet by turning the 2 side fasteners
and remove the screw on the grill.
24 • Plug battery terminal A into vehicle wiring
terminal B.
25 • Close the bonnet by turning the 2 side fasteners
and tighten the screw.
FEATURES AND INSTRUCTIONS
FOR USE
26 • Below the box you can find four removable toy
tools. To remove the box, pull out and unfasten
the four couplings.
27 • A: HORN. Push the yellow button the horn will
sound.
B: FM RADIO: a real removable car radio that
works independently. Press button 3 to turn it
on. Press button 4 to turn it off. Use the
triangular buttons to change the frequency with
automatic tuning. The station will not be
memorized when the radio is turned off. Use
knob 2 to adjust the volume. To adjust the time,
hold down the SET button and push the HR and
MIN buttons as appropriate.
The AUX (1) socket on the radio can be used
for connecting MP3 devices.
C: SIMULATED START-KEY. The key provided is
only a "toy key", and does not turn the vehicle
on or off.
D: Accelerator/electric brake pedal. The electric
braking system stops the vehicle automatically
when your child lifts his foot off the pedal.
28 • To unfasten the safety belts:1 push towards the
middle and simultaneously press the button; 2
detach the buckle.
29 • GEAR SHIFT LEVERS: 1: first speed. 2: second
speed. R: reverse.
30 • SECOND SPEED: When the red lock-out is
positioned as shown in the figure, the vehicle will
run in first speed and reverse only. The turtle on
the lock-out is in the up position. To use the
second gear, follow the instructions: loose the
screw on the red lock-out.
31 • Remove the red lock-out.
32 • Rotate it 180° until the hare is in the up
position. Insert the lock-out into the hole
provided.
33 • Tighten the screw. By pushing the gearshift lever
backward, the vehicle moves into second gear.

REPLACING THE BATTERY

PLEASE NOTE: THE PICTURES OF THE BATTERIES
ARE FOR ILLUSTRATIVE PURPOSES ONLY. YOUR
BATTERY MAY BE DIFFERENT FROM THE MODEL
SHOWN. THIS DOES NOT AFFECT THE
REPLACEMENT AND CHARGING PROCEDURES
DESCRIBED.
34 • Open the bonnet by turning the 2 side fasteners
and remove the screw on the grill.
35 • Unscrew and remove the battery fastener.
36 • Replace the battery. Replace the battery fastener.
37 • Connect the two plugs.
38 • Close the bonnet by turning the 2 side fasteners
and tighten the screw.
BATTERY RECHARGE
WARNING: BATTERY CHARGING AND EVERY
OTHER OPERATION ON THE ELECTRICAL
SYSTEM MUST BE CARRIED OUT BY ADULTS
ONLY.
THE BATTERY CAN ALSO BE CHARGED
WITHOUT REMOVING IT FROM THE TOY.
39 • Disconnect the electrical system terminal A from
the battery terminal B pressing with the fingers
on the sides.
40 • Plug the battery charger terminal to a wall outlet
following the instructions provided. Connect the
terminal B and the battery charger terminal C.
41 • Once the battery has been recharged, unplug the
battery charger from the wall outlet, then
disconnect terminals C and B.
42 • Connect terminal B and A till you hear the final
click. Once recharging is complete, don't forget
to close the simulated motor with the screw.