RIB Vertigo Wi-Fi Series Manual Del Usuario página 15

VERTIGO Wi-Fi in combination with the electronic device MASTER Wi-Fi
conforms to standard EN13849-2 (2008) and when used with a RIB
electronic control panel it is a Class 2 protection device for protecting
persons/things from collisions caused by mechanical moving parts such
as automatic gates or doors.
The obstacle is detected for the whole distance between the infrared
transmitter and receiver which constitute the VERTIGO Wi-Fi product.
VERTIGO Wi-Fi can be positioned anywhere without needing to use
electrical wire.
The Wi-Fi system (made up of a VERTIGO Wi-Fi and MASTER Wi-Fi)
operate at a frequency of 868,3 MHz.
The MASTER Wi-Fi board communicates constantly with VERTIGO Wi-Fi
and always indicates interruptions of the infrared signal between the TX
transmitter and the RX receiver or any type of malfunctioning.
Each VERTIGO Wi-Fi has its own internal ID code that distinguishes it from
the other devices.
The Wi-Fi system is an active security system because it constantly verifies
proper functioning of the VERTIGO Wi-Fi devices and battery condition.
When using RIB electronic control panels you can run auto-tests on the
system.
With RIB actuators, RIB electronic control panels having the auto-test
function and RIB safety devices you can create an installation that
conforms to the European Directives and Norms in force.
After completing the system, you must make sure it conforms to standard
EN13241-1.
RIB shall not be liable for any damages caused by improper, incorrect or
unreasonable use of the product.
R
EFERENCE TO STANDARDS FOR AUTOMATIC GATES
AND DOORS
RIB MAY NOT BE HELD RESPONSIBLE FOR DAMAGES CAUSED BY
IMPROPER, WRONG OR UNREASONABLE USE.
Usage restrictions: The VERTIGO Wi-Fi photocells cannot be used on
devices excluded by the application of the EN12978, such as:
- Protection devices for the installation on doors used for a different
purpose to those ones used for pedestrian or veheicle access, covered
by the norm which principal intent is that of allowing a safe access to
industrial, commercial, public and commercial sites. Some examples of
excluded accesses can be: sluice gates, dams, lift doors, vehicles' doors,
doors used mainly to restrain animals, theatre curtains, railways barriers,
barriers used only for vehicles.
- Devices used only fo the standard control and for the stopping, including
the emergency stopping, of motorized doors.
- Safety systems and safety devices used on machineries different from
doors.
ATTENTION: Any possible modification of the device, or of the configuration
of the same cannot be carried out without the clear authorization by the
manufacturer or, by the local authorized dealer.
The installer of the safety device must make sure that the end user know
the following:
- That the safety devices must be made known to all appropriate people.
- That the passages to reach the devices must be kept clear from any
obtsacle.
- About the procedures for cleaning so to avoid the dangerous building up
of material.
- The possible details for a restart of the system after an emergency or
accidental stop caused by the control system.
Any modification of the project or, of the configuration of the device, without
discussing it first with the manufacturer or with the local autorized dealer
can cause dangerous situations.
VERTIGO Wi-Fi PHOTOCELLS ARE ONLY ON DURING DOOR
OPERATION. THANKS TO THE SLEEP MODE. WHEN THE DOOR IS
NOT MOVING THE PHOTOCELLS ARE OFF TO ALLOW FOR LONGER
BATTERY LIFE.
VERTIGO Wi-Fi are produced in wall-type versions:
- VERTIGO Wi-Fi 8 code ACG8042
- VERTIGO Wi-Fi 10 code ACG8043
to be fasten to the primary and/or
secondary borders (mobile or fixed)
made of iron or other smooth material.
It is possibile, if necesary, to rotate
by 90° in 90° only the ray direction
in respect to the main structure
that contains the circuit (see picture
here aside).
A
PPLICATION
MAX
GATE DISPLACEMENT
WEIGHT
150 kg 13 m/min.
8
300 kg 10 m/min.
500 kg 13 m/min.
10
1000 kg 10 m/min.
M
OUNTING
VERY IMPORTANT!
When installing the VERTIGO
Wi-Fi photocell, besides following
the instructions in the chapter
"APPLICATION", verify that when
using a NOT RIB control panel, this
one must be complying with the
reaction time (inversion) requested
by the Norm EN12453 (requirements
of safety devices used on motorized
gates/doors).
PLACE THE RECEIVER OF THE
PHOTOCELL ON THE TOP OF THE
LEAF AND THE COLUMNS OF THE
GATE AND IN FULL VIEW OF THE
Wi-Fi MASTER BOARD.
THE VERTIGO Wi-Fi TRANSMITTER
MUST BE APPLIED TO THE BOTTOM
OF THE LEAF AND THE COLUMNS
OF THE GATE.
NO OBSTACLES SUCH AS WALLS,
PILLARS OR METAL CABINETS
MUST BE PRESENT BETWEEN THE
RECEIVER OF THE VERTIGO Wi-Fi
PHOTOCELLS AND THE MASTER
Wi-Fi BOARD.
If it is not possible to avoid that
because the obstacles cannot be
removed, please install an 868
MHz aerial (code ACG5451) on the
MASTER Wi-Fi and position it so
to guarantee a good quality radio
communication between the parts.
This solution also prevents the
quick discharge of the batteries on
the VERTIGO Wi-Fi.
* Before fastening the base of the
RECEIVER to the upper part of the leaf,
check for possible obstructions due
to potential stops and/or conveying
systems.
** Available space for potential mechanical
stop.
15
15
MAX
SPEED
RX
TX
Measurements in mm
G
B