RIB Vertigo Wi-Fi Series Manual Del Usuario página 18

G
B
INFRARED SIGNAL RECEIVER - RX
M
EMORIZATION
- Set the micro-switch 1 on the MASTER Wi-Fi board on "ON" position to enable
the pair of VERTIGO Wi-Fi photocells to store.
To perform memorization use the following procedure:
- Push the button PROG RX found on the MASTER Wi-Fi card => the dual-colored
LED EDGE PHOT 1 will flash red for 1 minute (the time necessary to perform
memorization).
DL2 PROG RX
- Push the button S3 PROG on the VERTIGO Wi-Fi receiver (Fig. 5) with micro-
switch 1 set to ON => on the MASTER Wi-Fi the dual-colored LED EDGE PHOT
1 flashing red will turn green and a buzzer will signal that memorization of the
photocell has been done correctly. At the same time on MASTER Wi-Fi the
dual-colored LED EDGE PHOT 2 will begin flashing red for 1 minute (the time
necessary to perform memorization*).
If there are no other photocells to be memorized let a minute pass or push the
button PROG. RX 4 times to complete the memorization procedure (the LED
EDGE PHOT 2 shuts off) => all of the LEDs EDGE PHOT should be off during
normal operation.
- Assemble the cover (7) attaching it to the base (8) on the bottom part using the
special tooth, and then close the cover (Fig. 6).
- Once the cover is closed, check that it is parallel to the base. Otherwise, open
it again and check that the circuit and the connection wires are correctly fitted
in their seats.
- Fasten the cover (7) to the base (8) with the 4 self-tapping screws TCCR2,9X9,5
supplied (11) (Fig. 6).
ATTACH THE YELLOW LABEL WITH THE IDENTITY NUMBER TO THE
COVER (supplied in the MASTER Wi-Fi packaging).
* TO MEMORIZE OTHER VERTIGO Wi-Fi PHOTOCELLS:
- Push the button S3 PROG on the VERTIGO Wi-Fi receiver with micro-switch
2 set to ON => on the MASTER Wi-Fi the dual-colored LED EDGE PHOT 2
flashing red will turn green and a buzzer will signal that memorization of the
photocell has been done correctly.
NOTE: at the end of the memorization procedure and after having enabled the
micro-switches for the safety devices memorized on the MASTER Wi-Fi, run a
scan on the dual-colored LED EDGE PHOT pushing the button PROG. RX 6
times.
- If, after closing the cover with the RX bellow, the led should remain on, this
means that the photocells are already correctly aligned. The led will remain on
for 5 minutes, in order to carry out functional checks.
- If the red led remains switched off after closing the protective cover, for no more
than 5 minutes, check for correct alignment (as in the illustration)and for any
deformation of the bellows; after the checks, the red led should light on.
S
YSTEM CHECK
After finishing the mounting procedure, check the correct working order between
the VERTIGO Wi-Fi photocells and the MASTER Wi-Fi by doing the following:
- Check that the red led on the infrared receiver RX VERTIGO Wi-Fi is on.
Otherwise, press the pushbutton S3 PROG to light on the red led for 5 minutes.
- Place an object between them and check that the red LED turns off and that at
the same time on the MASTER Wi-Fi the corresponding LED EDGE PHOT is on
and green while the object is present.
- The LED DL2 of the MASTER Wi-Fi should also turn off indicating the correct
exchange of dedicated contact with the EDGE entry on the motor control panel.
- Repeat the process on the other VERTIGO Wi-Fi photocells installed.
- Then perform a system check of all the photocells installed by activating the
movement of the automation and checking that when an object is present the
automation stops/reverses when closing, or stops/continues to open when
opening.
DUAL-COLORED LED EDGE PHOT
12/24V ac/dc
C
LOSING THE VERTIGO CONTAINERS
Lastly, place the screw cover caps (6) (12) both on the TX and on the RX of the
VERTIGO Wi-Fi (Fig. 2-6), by inserting them into the 4 holes so that they are
perfectly attached.
A
NTENNA
The radio antenna is already connected to all of the VERTIGO Wi-Fi receivers.
DO NOT TOUCH IT !!!
W
ARNING
(notice about replacing the batteries, indicated by MASTER Wi-Fi)
The WARNING tells the user of the immediate need to replace the batteries.
When battery power reaches 2,3V, the photocell receiver signals the MASTER
Wi-Fi via radio of the low battery status and activates the BUZZER of the MASTER
Wi-Fi with a sound every 3 seconds for 1 minute.
The warning is renewed for 1 minute if a command is given to the door.
The dual-colored LED on the MASTER Wi-Fi of the photocell with the low batteries
emits a constant red light.
The system is still operational during these signals, but it is advantageous to
replace the batteries as soon as possible in order to avoid a full stop of the door
operation which happens when the batteries reach 2,0 V.
ATTENTION: The SPARK Wi-Fi flashing light changes flash modes during the
warning status; flashing 2 times in quick succession followed by a 2 second pause.
A
LARM STATUS (indicated by MASTER WI-Fi)
The alarm activates when the batteries have been exhausted (2,0 V) or when a
photocell is not working.
On the MASTER Wi-Fi LEDs DL2 and DL3 turn off, stopping the automation due
to the fact that one of the photocells installed is not working properly.
On the MASTER Wi-Fi the LED of the photocell with the low or exhausted battery,
alternates red to green and the buzzer emits an intermittent sound for 1 minute to
alert the user that the batteries or the photocell need attention.
The alarm is renewed for 1 minute if a command is given to the door.
IN ORDER TO REMOVE THE SINGLE PHOTOCELL FROM THE Wi-Fi SYSTEM
READ THE MASTER Wi-Fi CARD MANUAL.
C
HANGING THE BATTERIES
The duration of the batteries used for VERTIGO Wi-Fi photocells is about 3 years.
- Identify which photocell has the exhausted batteries by looking at the LED
EDGE-PHOT on the MASTER Wi-Fi card.
- Identify through the use of the number of the pair of photocells with the
exhausted batteries on the side of the dual-colored LED that:
- alternately flash red to green (if the alarm is on)
- has a constant red light (if the warning is on)
- has a constant green light (if the VERTIGO Wi-Fi transmitter batteries are
exhausted)
- Locate the adhesive strip with the corresponding identity number of the
photocells on the outside of the container.
- Replace the batteries of both the transmitter and receiver checking that the
polarity is correct.
- Push the button S3 PROG of the photocell receiver to reactivate the MASTER
Wi-Fi. The buzzer on the edge of the MASTER Wi-Fi card turns off and the LED
DL2- DL3 (if the alarm is on) turn on and the dual-colored LED of the photocell
with the replaced batteries turns off.
The automation is now ready to begin safe operation once more.
ATTENTION: Please remember that batteries must be disposed of properly
according to current standards. In case of disposal of the photocells please
remember to remove and dispose of the batteries properly.
R
EMOVAL PROCEDURE FOR A SINGLE VERTIGO Wi-Fi FOR BREAKDOWN
OR SUBSTITUTION
In order to remove a single memorized VERTIGO on the MASTER Wi-Fi, use the
following procedure:
- Push the button PROG. RX one or more times to select the dual-color LED
EDGE PHOT which begins flashing green, corresponding to VERTIGO to be
eliminated.
- After selecting the photocell, push and hold the button PROG. RX for 10
seconds.
- After 10 seconds the dual-color LED EDGE PHOT flashes alternately red and
green 6 times, indicating successful removal.
WARNING: Turn the micro-switch for the eliminated VERTIGO on "OFF" position
and press the PROG. RX pushbutton 6 times to carry out the
scanning of the two-coloured leds.
18 18
18 18