Tabla de contenido
Publicidad
Abbr.
Name
RM
RunMode
CF
ConnectionFaulted
DA
DiagnosticActive
DSC
DiagnosticSequenceCount
FI.ES
EstopStatus
FI.EN
EnablingSwitchStatus
FI.MS0 ModeSelectPos1
FI.MS1 ModeSelectPos2
FI.MS2 ModeSelectPos3
FI.D
DoorStatus
FI.B
BoltStatus
FI.L
SolenoidStatus
FI.SK
InterlockStatus
FI.UK
GuardLockStatus
Sxx.1
OpxPos1
Sxx.2
OpxPos2
D.PF
PlausibilityFault
D.ES
EstopFault
D.EN
EnablingSwitchFault
D.MS
ModeSelectFault
D.OL
LockCommandFault
D.LT
CycleCount
FaultCode
FO.L
LockCommand
Hxx
OpxIndicator
STx
StacklightControl
Q.G
GeneralFaultAck
Q.PF
PlausibilityFaultAck
EN-Sx
EnablingSwitchOpxPos
EN-Hx
EnablingSwitchOpxIndicator
2126330-08-06/19 (Traducción del manual de instrucciones original)
MGB-L..B-EI-... (Ethernet/IP) y con estructura de datos de tipo A
Data Type
Safe signal Tag Definition
BOOL
No
Run Mode - Indicates the operating mode of the multifunctional gate box
0 = while restarting
1 = Run Mode after successful restarting of bus module
BOOL
No
Connection Faulted - Indicates the state of the communication connection between the multifunctional gate
box and the controller.
0 = Connection of output data
1 = Connection of output data Faulted
BOOL
No
Diagnostic Active - Indicates whether the multifunctional gate box is faulted.
0 = No Fault
1 = Fault
SINT
No
Diagnostic Sequence Count - Displays the total accumulated diagnostic counts.
Values range from 0...255.
BOOL
Yes
E-stop Button Status
1 = Contacts Closed (E-stop not pressed)
0 = Contacts Open (E-stop pressed)
BOOL
Yes
Enabling Switch Status
1 = Switch Enabled
0 = Released
BOOL
Yes
Mode Selector Switch Position 1
1 = Selector Switch in position 1
0 = Selector switch is not in position 1
BOOL
Yes
Mode Selector Switch Position 2
1 = Selector Switch in position 2
0 = Selector switch is not in position 2
BOOL
Yes
Mode Selector Switch Position 3
1 = Selector Switch in position 3
0 = Selector switch is not in position 3
BOOL
Yes
Door Status - position of the guard door
0 = guard door is OPEN
1 = guard door is CLOSED
BOOL
Yes
Bolt Status - position of the bolt actuator
0 = bolt is retracted
1 = bolt is extended
BOOL
Yes
Solenoid Status - position of the solenoid locking arm
0 = locking arm is in unlocked position
1 = locking arm is in locked position
BOOL
Yes
Interlock Status
0 = bolt retracted and/or door OPEN
1 = door is CLOSED and bolt is extended
BOOL
Yes
Guard Lock Status
0 = door is OPEN, or door is CLOSED with bolt retracted, or door is CLOSED with bolt extended and
unlocked
1 = door is CLOSED, bolt is extended, and bolt is locked
BOOL
No
Operator Position 1
1 = Pressed (push button) or right position (selector switch)
0 = Released (push button)
or 2-position selector switch in middle position
or 3-position selector switch in midle or left position
x = 1, 2, 3, 4, 90, 91, 92, 93, 94, 95
BOOL
No
Operator Position 2
1 = left position (3-position selector switch)
0 = released push button
or 2 position selector switch in right or middle position
or 3 position selector switch in middle position
x = 1, 2, 3, 4, 90, 91, 92, 93, 94, 95
BOOL
No
Plausibility Fault - indicates a signal sequence error (lock module error), unlocking sequence
BOOL
No
Estop Fault - indicates an E-stop specific fault
BOOL
No
Enabling Switch Fault - indicates an Enabling Switch specific fault
BOOL
No
Safe Mode Selector Switch Fault - indicates a Mode Selector Switch specific fault
BOOL
No
Lock Command Fault - indicates a fault in the Lock Command
BOOL
No
Cycle Count - indicates when the device has reached 1,000,000 switching cycles
0 = < 1,000,000 swtiching cycles of the solenoid
1 = > 1,000,000 switching cylcles of the solenoid
SINT
No
Fault Code - indicates the specific diagnostic message of the multifunctional gate box
BOOL
Yes
Lock Command - control for switching the guard locking on and off
0 = Guardlocking is locked
1 = Guardlocking is unlocked
BOOL
No
Operator Indicator - controls illumination of the operator
1 = illumination is turned ON
0 = illumination is turned OFF
x = 1, 2, 3, 4, 90, 91, 92, 93, 94, 95
BOOL
No
Stacklight Indicator - controls illumination of the stacklight
1 = illumination is turned ON
0 = illumination is turned OFF
x = 1, 2, 3, 4
BOOL
No
General Fault Acknowledgement - resets the bus module
1=Reset of bus module
0=normal operation of device
BOOL
No
Plausibility Fault Acknowledgement - resets the lock module
1=Reset of locking module
0=normal operation of device
BOOL
No
Enabling Switch Operator Position
1 = pressed (push button)
0 = released (push button)
BOOL
No
Enabling switch Operator Indicator - controls illumination of the operator
1 = illumination is turned ON
0 = illumination is turned OFF
Manual de instrucciones Sistemas de seguridad
ES
27
Publicidad
Tabla de contenido
