Nice Era Mat VS Instrucciones Y Advertencias Para La Instalación Y El Uso página 7

After about 10 seconds, the motor performs a number of movements equal to the number impulses given with the transmitter.
04. (on the new transmitter) Press the same key as you pressed in point 01 and hold it down while the motor performs 3 movements. Upon completion, release the
key. Warning! If the motor performs 6 movements, it means that its memory is full.
01
example
8
sec.
New
03
Old
same
04
01
New
5.9 - Memorisation of a climate sensor connected via radio
To perform the procedure you must have a transmitter ("old") already memorised in "Mode 1".
01. (on the climate sensor) Keep the yellow key pressed for 10 seconds and then release it (in this case the motor does not perform any movement).
02. (on the old transmitter) Press any key which has already been memorised three times (the motor will start performing the manoeuvre associated with that key).
03. (on the climate sensor) Keep the yellow key pressed for 2 seconds: the motor performs 3 movements to confirm the memorisation. Warning! If the motor per-
forms 6 movements, it means that its memory is full.
01
"P1"
Note – When performing the procedure, you can cancel it at any time by keeping the n and t keys pressed simultaneously for 4 seconds. Otherwise, do not press
any key and wait 60 seconds for the motor to perform 6 movements.
5.10 - Total or partial deletion of memory
This procedure allows you to choose under point 05 the data that you want to delete.
5.10.1 - Procedure performed with a transmitter memorised in "Mode I"
01. Keep the n key pressed and wait for the motor to perform 2 movements. Upon completion, release the key.
02. Keep the s key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
03. Keep the n key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
04. Keep the t key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
05. • To cancel the entire memory: Keep the s and t keys pressed and wait for the motor to perform 5 movements. Upon completion, release the keys.
• To delete all memorised transmitters: do not press any key and wait until the motor performs 5 movements.
• To delete a single memorised transmitter: hold down the s key and wait for the motor to perform 3 movements. Now release the key.
button of the transmitter you wish to delete: the motor performs 5 movements.
• To delete the limit switch heights ("0", "1") and intermediate heights ("H"): WARNING: – This deletion must be performed only when you want
to adjust the limit switch heights again, using a different procedure than the one used previously. Keep the n key pressed and wait for the motor to
perform 5 movements. Upon completion, release the key.
01
5
2
sec.
04
5
sec.
02
Old
x 1 = Up x 1 = Salita
x 2 = Up after 10 seconds x 2 = Salita dopo 10 secondi
x 3 = Up after 20 seconds x 3 = Salita dopo 20 secondi
x 4 = Down x 4 = Discesa
x 5 = Down after 10 seconds x 5 = Discesa dopo 10 secondi
0,5 x 6 = Down after 20 seconds x 6 = Discesa dopo 20 secondi
sec.
x 7 = Step-by-step x 7 = Passo-passo
x 8 = Stop x 8 = Stop
5
3
sec.
02
"P1"
1 0
sec.
Old
02
5
sec.
all
data
5
4
sec.
10
?
sec.
Note – When performing the procedure, you can cancel it at
any time by keeping the n and t keys pressed simultaneous-
ly for 4 seconds. Otherwise, do not press any key and wait 60
seconds for the motor to perform 6 movements.
03
example
X 3
0,5
sec.
3
05
5
sec.
1 /
2 /
3 /
.../
"P1"
2
sec.
03
5
3
sec.
05
all
3
Lastly, press the
English – 6