Care And Cleaning - American Standard CADET 3 Serie Manual De Instalación Y Manual Del Usuario

10
TOP
CRITICAL LEVEL
MARK ("C.L.")
MUST BE
1" ABOVE
OVERFLOW PIPE
FLOAT
CUP
FILL
VALVE
VALVE
BODY
ADJUSTABLE
HEIGHT
LOCK NUT
CONE WASHER
COUPLING NUT
(HAND TIGHT ONLY)
12

CARE AND CLEANING

When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth. Avoid detergents,
disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or abrasive pads on your toilet seat.
Some bathroom chemicals and cosmetics may damage the seat's finish.
WARNING:
Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the
!
tank. This damage can cause leakage and property damage.
American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing
chlorine (calcium hypochlorite).
Repair parts are determined by toilet tank number which can be found marked inside tank.
PART NUMBER
738903-XXX0A
034783-XXX0A
738565-423.0070A
738921-100.0070A
738921-101.0070A
738921-102.0070A
738920-100.0070A
738921-103.0070A
738921-104.0070A
738921-105.0070A
7381026-400.0070A
7301021.0070A
738916-100.0070A
738916-101.0070A
5332.016.XXX
738565-442.0070A
5331.016.XXX
7381043-400.0070A
735122-400-XXX0A
735121-400-XXX0A
735123-400-XXX0A
ARM
REFILL
NIPPLE
TUBE
TANK
LEVER
FLUSH
VALVE
WATER LEVEL
ADJUSTMENT
ROD
FLAPPER
SHANK
WASHER
THREADED
SHANK
PARTS FOR WATER
CONNECTION
(SEE STEP 9)
Diagram 1
REPAIR PARTS LIST
NOTE: "XXX" represents color or trim finish options. Specify when ordering.
DESCRIPTION
Tank Lever LH
Bolt Cap Kit
Fluidmaster 400A Inlet
Flushvalve Assembly - 1.6 GPF
Flushvalve Assembly - 1.6 GPF
Flushvalve Assembly - 1.6 GPF
Flapper Assembly - 1.6 GPF
Flushvalve Assembly - 1.28 GPF
Flushvalve Assembly - 1.28 GPF
Flushvalve Assembly - 1.28 GPF
Flapper Assembly 1.28 GPF
Tank Coupling Kit 252
Refill Tube - 5 inch
Refill Tube - 9 inch
Elongated Seat
Fluidmaster 400A Inlet
Round Front Seat
Flapper Assembly - 1.28 GPF w/Float
10" Tank Cover
12" Tank Cover
14" Tank Cover
ADJUSTMENTS
a. Adjust water level. Water level should
be adjusted to level indicated on tank
by adjusting float cup.
See Step 11 for water level adjustment
method
b. If bowl fails to siphon, an adjustment
may be required with the lift chain.
Simply remove the bead chain from
the retainment clip and take up slack
on the chain, and reinsert on lift rod.
Make sure the chain is not too taught.
1.6 GPF
√ √ √ √
√ √ √ √
√ √ √ √
√
√ √
√
√ √ √ √
√ √ √ √
√ √
√ √
√
√ √
√
√
- 3 -
11
Turn on water supply.
Submerge the FLOAT CUP
under the water for 30
seconds. Adjust the water to
desired level by turning
WATER LEVEL ADJUSTMENT
ROD and moving FLOAT CUP
up or down.
1.28 GPF
√ √ √ √ √ √
√ √ √ √ √ √
√ √ √ √
√
√ √
√ √
√
√
√
√
√ √ √
√ √ √ √ √ √
√ √ √ √
√
√
√ √
√
√
√
√
√
√ √ √ √
√
73 0 92 8 - 1 0 0 R e v. G
√ √
√ √
√
√
√
√
√ √
√
√
√ √
√
√
√
√