MIDI data format
2.1.5 OUT/THRU
Select whether the MIDI OUT/THRU connector will
function as OUT or as THRU.
If THRU is selected, messages received at the MIDI IN
connector will be re-transmitted without change from the
MIDI OUT/THRU connector.
Regardless of the MIDI/HOST setting, the connector will
function as a THRU connector if the THRU setting is
selected. If you want to use the connector as MIDI OUT,
the MIDI/HOST setting must be OUT.
2.1.6 TO HOST
If the TO HOST connector is selected, choose one of
three settings depending on the type of computer that is
connected.
2.1.7 MIDI Clock ON/OFF
Specify whether MIDI Clock will be used.
If this is ON, MIDI Clock will be transmitted from the
connector selected by MIDI/HOST.
2.1.8 MTC ON/OFF
Select whether MTC will be used.
If this is ON, MTC will be transmitted from the connector
selected by MIDI/HOST.
Regardless of this setting, MTC will always be transmitted
from the MTC OUT connector.
2.2 Program change assign table
This table allows you to freely specify the correspon-
dence between Program Change No. and Scene No.
This table is used for conversion for both transmission
and reception.
2.3 Control change assign table
This table allows you to freely specify the correspon-
dence between Control Change No. and Parameter
name.
This table is used for conversion for both transmission
and reception.
3. MIDI format list
3.1 CHANNEL MESSAGE
command
rx/tx
-------------------------+-----+---------------------------------------
8n NOTE OFF
rx
Control the internal effect
9n NOTE ON
rx
Control the internal effect
Bn CONTROL CHANGE rx/tx Edit parameters (use the Control
Change Assign Table)
Cn PROGRAM CHANGE rx/tx Switch scene memories (use the
Control Change Assign Table)
3.2 SYSTEM COMMON MESSAGE
command
rx/tx
-------------------------+-----+---------------------------------------
F1 MIDI TIME CODE rx/tx MTC transmission (when MTC
Master), MTC reception (when
MTC slave)
F2 SONG POSITION POINTER tx
SPP reception (when MIDI Clock
is used)
3.3 SYSTEM REAL TIME MESSAGE
command
rx/tx
-------------------------+-----+---------------------------------------
F8 TIMING CLOCK tx
MIDI Clock transmission (when
MIDI Clock is used)
FA START
tx
Start command transmission
(when MIDI Clock is used)
FB CONTINUE
tx
Continue command transmission
(when MIDI Clock is used)
FC STOP
tx
Stop command transmit (when
MIDI Clock is used)
38
FE ACTIVE SENSING rx
FF RESET
3.4 SYSTEM EXCLUSIVE MESSAGE
3.4.1 Real Time System Exclusive
3.4.1.1 MMC
-------------------------+-----+---------------------------------------
01 STOP
02 PLAY
03 DEFERRED PLAY rx/tx
04 FAST FOWARD rx/tx
05 REWIND
06 RECORD STROBE rx
07 RECORD EXIT
0F RESET
40 WRITE
44 LOCATE
3.4.2 Bulk Dump & Request
data
name
-----+-------+------------------------------------
'M'
'S'
'R'
'Q'
'Y'
'E'
'T'
'H'
'A'
'P'
'C'
3.4.3 Parameter Change
Parameter
type
-----+-------+------------------------------------
0x00
0x01
0x02
0x10
0x40
0x41
0x43
4. MIDI format details
function
4.1 NOTE OFF (8n)
< Reception >
Received when [Rx CH] matches.
Used to control effects. Refer below for details.
STATUS
DATA
4.2 NOTE ON (9n)
function
< Reception >
Received when [Rx CH] matches.
Used to control effects. Refer below for details.
Velocity of 0x00 is equivalent to Note-Off.
STATUS
DATA
* Effect control by Note
function
1: Dynamic Flange/Dynamic Phase/Dynamic Filter
When the SOURCE parameter is set to MIDI, the note
velocity (both note-on and note-off) is used to control the
Modulation frequency width.
Version 2.0 Apéndice del manual
Check MIDI cable connections
rx
Clear running status
command
rx/tx
rx/tx Transport stop
Transport play
rx
Transport play
Transport fast-forward
Transport rewind
rx/tx
Transport punch-in record
Transport punch-out
rx
MMC reset
rx/tx
Write data field
rx
Transport locate
rx/tx
rx/tx
function
rx/tx
Scene Memory & Request
rx/tx
Setup Memory & Request
rx/tx
Remote Memory & Request
rx/tx
Equalizer Library & Request
rx/tx
Dynamics Library & Request
rx/tx
Effect Library & Request
rx/tx
Patch Library & Request
rx/tx
Channel Library & Request
rx/tx
Automix Memory & Request
rx/tx
Program Change Assign Table & Request
rx/tx
Control Change Assign Table & Request
rx/tx
function
rx/tx
edit buffer (byte operation format)
rx
system memory (byte operation format)
rx/tx
function call (mem/lib recall,mem/lib
store)
rx/tx
edit buffer (7bit operation format)
rx/tx
edit buffer (bit operation format)
rx
system memory (bit operation format)
rx
controller (key remote) (bit opera-
tion format)
1000nnnn 8n
Note Off Message
0nnnnnnn nn
Note No.
0vvvvvvv vv
Velocity ( ignored)
1001nnnn 9n
Note On Message
0nnnnnnn nn
Note No.
0vvvvvvv vv
Velocity (1-127:On, 0:off)
function