Manuales relacionados para Serta 46033
Resumen de contenidos para Serta 46033
- Página 1 Novo Serta Ergonomic ® Mesh Chair Silla de malla ergonómica Serta ® Assembly Instructions Instrucciones de ensamblaje MODEL / MODELO 46033 Soporte m ximo á de la silla: 136 kg 300 lbs...
-
Página 2: Instrucciones De Ensamblaje
Chair Assembly Instructions Carefully unpack all parts and identify them against the parts list before attempting to assemble. To avoid scratching the components, assemble the chair on a protected surface. Note: The casters sold with this chair are intended for use on carpet and not recommended for use on tile or hard wood floors. - Página 3 PARTS/PARTES PARTS/PARTES Casters Star Base Gas Lift Seat Cushion with Seat Plate Ruedas Elevador neumático Base en forma de estrella Cojín del asiento y Mecanismo Quantity/cantidad: 5 del asiento Quantity/cantidad:1 Quantity/cantidad: 1 Quantity/cantidad: 1 Left Arm Right Arm 25mm Screws Back Cushion Brazo izquierdo Brazo derecho...
- Página 4 Step 1 Place the Star Base (B) upside down and insert 5 Casters (A) into the holes on the Star Base (B). Paso 1 Ponga la base en forma de estrella (B) con las patas hacia arriba y inserte las 5 ruedas (A) en los hoyos situados en la base (B).
- Página 5 Step 3 Place the assembled Seat Cushion with Seat Plate (D) on top of the Gas Lift (C) and press down until fully engaged. Paso 3 Coloque el cojín del asiento ensamblado a la mecanismo del asiento (D) sobre el elevador neumático (C) y presione hacia abajo hasta que queden totalmente enganchados.
- Página 6 Step 4 Insert the Arms (E1 & E2) to the bottom of the seat frame (with the front of arms facing the front of seat cushion) and attach by using 25mm Screws (G). *Note : Tighten the screws completely. Paso 4 Inserte los brazos (E1 y E2) en la parte inferior del bastidor del asiento (con la parte delantera de los brazos mirando hacia la parte delantera del cojín del...
- Página 7 Step 5 Insert assembled Back (F) into the Seat Cushion (D) as shown. Then secure with 15mm Screws (H). *Note : Tighten the screws completely. Paso 5 Inserte el respaldo (F) en el cojín del asiento (D), como se muestra en la figura. A continuación, fije con los tornillos de 15mm (H).
-
Página 8: Function Instruction
Operating Instructions Instrucciones de Uso Function Instruction - 1 To Adjust Seat Height : While seated, lean forward and reach under the right side of the chair to find the lever. Lift the lever and raise your body up slightly to allow the chair to rise to the desired height. Once desired height is reached, release lever to lock chair at desired height. - Página 9 Function Instruction - 2 To Operate Tilt Lockout : While seated, reach under the left side of the chair to find the lever 1. Push down the lever and lean back to allow the chair to tilt backwards. Pull the lever to the up position to lock the chair angle while the desired position is reached.
- Página 10 Function Instruction - 3 To Adjust Tension On The Tilt : Reach under the front center of the chair, grasp the round knob (R) and turn it counter- clockwise to stiffen the tilt mechanism for a heavier user. Turn the knob (R) clockwise to loosen the tilt mechanism for a lighter user.
- Página 11 Function Instruction - 4 To Adjust Seat Depth : While seated, reach under the left side of the chair to find the lever 2. Lift lever and adjust the seat depth short enough to enable your legs to move freely under the chair. To adjust seat depth, lift the lever 2 and slide the seat into the preferred position.
- Página 12 Function Instruction - 5 To Adjust Lumber support Height : Lumber support height adjust independently for the short and tall. Instrucciones de Funcionamiento - 5 Para ajustar la altura del soporte lumbar : La altura del soporte lumbar se ajusta independientemente para bajos y altos.
- Página 13 Function Instruction - 6 To Adjust Arm Height : Press the buttons on the chair arms. Press the buttons to allow the arms to move up or down freely then release the buttons once the desired height is reached. Instrucciones de Funcionamiento - 6 Para ajustar la altura de los brazos : Presione los botones de los brazos de la silla.
- Página 14 Limited Warranty True Innovations seating products are warranted against defects in material and workmanship while owned by the “Original Purchaser”. The term “Original Purchaser” is defined as that party or entity which purchases True Innovations furniture from an authorized True Innovations retailer as shown by the original sales receipt.
- Página 15 Garantía Limitada Los productos de True Innovations seating están garantizados contra defectos de material y mano de obra mientras está en posesión de su “Comprador Original”. El término “Comprador Original” se define como el individuo o entidad que compra el mueble de True Innovations de un distribuidor autorizado así...