Balluff BTL5-H1 Serie Manual De Instrucciones página 10

BTL5-H1_ _-M_ _ _ _-P-S92/KA_ _
Micropulse Linear Transducer in Profile Housing
Contents
1 Safety Advisory .................... 2
1.1 Proper application ................. 2
1.2 Qualified personnel ............... 2
1.3 Use and inspection ............... 2
1.4 Scope ..................................... 2
2 Function and
Characteristics ..................... 3
2.1 Characteristics ...................... 3
2.2 Function ................................. 3
2.3 Available stroke lengths
and magnets .......................... 3
3 Installation ............................ 3
3.1 Transducer installation .......... 3
3.2 Floating magnets ................... 4
3.3 Captive magnets ................... 5
3.4 Using several magnets ......... 5
4 Wiring .................................... 6
5 Startup .................................. 7
5.1 Check connections ................ 7
5.2 Turning on the system ........... 7
5.3 Check output values ............. 7
5.4 Check functionality ................ 7
5.5 Fault conditions ..................... 7
5.6 Noise elimination ................... 7
6 Versions (indicated on
part label) .............................. 7
7 Configuration ....................... 7
7.1 Default settings ..................... 7
7.2 Presettings ............................. 7
8 Technical Data ...................... 8
8.1 Dimensions, weights,
ambient conditions ................ 8
8.2 Supply voltage (external) ....... 8
8.3 Control signals ....................... 8
8.4 Connection to processor ....... 8
8.5 Included in shipment ............. 8
8.6 Magnet ................................... 8
8.7 Accessories (optional) ........... 8
The following patents have been
granted in connection with this
product:
US Patent 5 923 164
Apparatus and Method for Auto-
matically Tuning the Gain of an
Amplifier
2
english
1 Safety Advisory
Read this manual before installing
and operating the Micropulse trans-
ducer.
1.1 Proper application
The BTL5 Micropulse transducer is
intended to be installed in a ma-
chine or system. Together with a
controller (PLC) or a master it com-
prises a position measuring system
and may only be used for this pur-
pose.
Unauthorized modifications and
non-permitted usage will result in
the loss of warranty and liability
claims.
1.2 Qualified personnel
This guide is intended for special-
ized personnel who will perform the
installation and setup of the system.
1.3 Use and inspection
The relevant safety regulations must
be followed when using the trans-
UL authorization
File No.
E227256
The CE Mark verifies
that our products meet
the requirements of
EC Directive
89/336/EEC (EMC Directive)
and the EMC Law. Testing in our
EMC Laboratory, which is accred-
ited by DATech for Testing Electro-
magnetic Compatibility, has con-
firmed that Balluff products meet
the EMC requirements of the fol-
lowing Generic Standards:
EN 61000-6-4 (emission)
EN 61000-6-2 (noise immunity)
ducer system. In particular, steps
must be taken to ensure that should
the transducer system become de-
fective no hazards to persons or
property can result. This includes
the installation of additional safety
limit switches, emergency shutoff
switches and maintaining the per-
missible ambient conditions.
1.4 Scope
This guide applies to the model
BTL5-H1...P-S92/KA... Micropulse
transducer.
An overview of the various models
can be found in section 6 Versions
(indicated on product label) on
page 7.
Note: For special versions, which
are indicated by an -SA_ _ _ des-
ignation in the part number, other
technical data may apply (affect-
ing calibration, wiring, dimensions
etc.).
Emission tests:
RF Emission
EN 55011 Group 1, Class A
Noise immunity tests:
Static electricity (ESD)
EN 61000-4-2 Severity level 3
Electromagnetic fields (RFI)
EN 61000-4-3 Severity level 3
Fast transients (Burst)
EN 61000-4-4 Severity level 3
Surge
EN 61000-4-5 Severity level 2
Line-induced noise induced by
high-frequency fields
EN 61000-4-6 Severity level 3
Magnetic fields
EN 61000-4-8 Severity level 4