Allgemeine Sicherheitstech; Bestimmungsgemässe Ver; Nicht Bestimmungsgemässe; Eg-Konformitätserklärung - SUHNER LWG 8 Documentación Técnica

Ocultar thumbs Ver también para LWG 8:
Tabla de contenido

Publicidad

1.1
Allgemeine sicher-
heitstechnische Hin-
weise
Diese Betriebsanleitung gilt für
die Maschine LWG 8.
Nur qualifiziertes Personal darf
die Maschine handhaben.
1.2
Bestimmungsgemässe
Verwendung
Die Maschine ist bestimmt zum
Trennen, Schleifen und Bürsten
von Metall- und Steinwerk-
stoffen.
Die Maschine ist ausschliesslich
für die 2-Hand-Anwendung vor-
gesehen.
1.3
Nicht bestimmungsge-
mässe Verwendung
Alle andern als die unter Pkt. 1.2
beschriebenen Verwendungen
gelten als nicht bestimmungs-
gemässe Verwendung und sind
deshalb nicht zulässig.
1.4
EG-Konformitätserklä-
rung (Original)
Otto Suhner GmbH, Trottäcker
50, D-79701 Bad Säckingen er-
klärt hiermit in alleiniger Verant-
wortung, dass das Produkt mit
der Serien- oder Chargen-Nr.
(siehe Rückseite) den Anforde-
rungen der Richtlinie 2006/42/
EG
entspricht.
4
DE
1.1
Indications générales
de sécurité
Ce dossier technique est va-
lable pour la machine LWG 8.
Seul le personnel qualifié peut
opérer sur la machine.
1.2
Utilisation conforme à
la destination
La machine est destinée à la
séparation, à meuler, et au bros-
sage de métaux et de pierre.
La machine est prévue exclu-
sivement pour une utilisation à
deux mains.
1.3
Utilisation contraire à
la destination
Toutes les applications autres
que celles décrites au point 1.2
sont à considérer comme con-
traires à la destination et ne sont
donc pas admissibles.
1.4
Déclaration de confor-
mité CE
Otto Suhner GmbH, Trottäcker
50, D-79701 Bad Säckingen
déclare par la présente, sous
sa seule responsabilité, que le
produit portant le numéro de
série ou de lot (voir verso) est
conforme aux exigences des
Angewandte
directives 2006/42/EG. Normes
FR
1.1
General notes on
safety
This operation manual is appli-
cable for the machine LWG 8.
The machine may only be han-
dled by personnel who are qual-
ified.
1.2
Use of the machine for
purposes for which it
is intended
The machine ist intended for the
cutting, grinding and brushing
of metal and stone materials.
The machine is intended exclu-
sively for 2-hand working oper-
attions.
1.3
Incorrect use
All uses other than those de-
scribed under section 1.2 are
regarded as incorrect use and
are therefore not admissible.
1.4
EC declaration of con-
formity
Otto Suhner GmbH of Trot-
täcker 50, D-79701 Bad Säck-
ingen, hereby declares under
sole responsibility that the prod-
uct with the serial or batch no.
(see reverse side) complies with
the requirements under the Di-
rective
GB
2006/42/EG.
Applied

Publicidad

Tabla de contenido
loading

Tabla de contenido