Sony PXW-X200 Manual Del Usuario página 6

Attaching method of the wireless LAN module (CBK-WA02
(sold separately))
1. Open the cover of the external device connector.
2. Attach the network module extension adapter (CBK-NA1E)
supplied with the wireless LAN module CBK-WA02 (sold
separately) to the camcorder.
Connect the convex terminal to the external device connector
on the camcorder and connect the wireless LAN module to the
concave terminal. You can attach the adaptor to the screw hole
(1/4 in.) of the accessory shoe mount.
3. Attach the wireless LAN module to the network module
extension adapter.
Note
Attach/remove the wireless LAN module while the camcorder is
turned off.
Major functions updated with V2.0
Notes
• You are required to update the camcorder software and the
network function software. Update the camcorder software first,
then update the network function software.
• When the camcorder software update is complete, "Version
Upgrade/OK: Turn Power Off" appears. If you leave it as it is, the
error message "E-31001" may appear. Since the update is
complete, just turn the camcorder off and on.
• For details of the operation methods concerning additional
functions, refer to "About Additional Functions" (PDF file). You
can download "About Additional Functions" from the Sony web
site.
Addition of the function for high-quality streaming by
Sony QoS technology
By providing the newly prepared network client mode, when
used with the Sony network RX station PWS-100RX1 (sold
separately), high-quality streaming is supported by Sony QoS
technology via the LTE/4G network.
• The connection setting can be set in "NW Client Mode" > "CCM
Address, " "CCM Port, " "User Name, " "Password" of the NETWORK
SET menu.
• The network client mode can be turned on/off in "NW Client
Mode" > "Setting" in the NETWORK SET menu.
• When the network client mode is selected, the setting and
control related to streaming are performed via PWS-100RX1.
• In the Device Status screen of the camcorder's built-in Web
menu, you can confirm the status of the network client mode.
Notes
• When switched to the network client mode, streaming,
monitoring, proxy recording, or file transferring cannot be
performed.
• When switched to the network client mode during monitoring,
proxy recording, or file transferring, these operations stop.
About acquiring the positioning information (GPS)
You can record the positioned information to the proxy data via
GPS.
Recording of the proxy data's still images
When proxy recording is performed, the still image of proxy data's
first frame is recorded simultaneously.
Displaying the proxy data's thumbnails
You can display the proxy data's thumbnails quickly using the first
frame's still image.
Transferring the proxy data partially
When you use the Content Browser Mobile application V2.0 or
later, you can transfer the clipped partial data by specifying the
in-point and out-point from the proxy data.
Notes
• The maximum 15-frame margin is attached in front and behind
the clipped point in a generated file.
• When you clip the proxy data recorded with network function
software V1.32 or earlier, the data may not be taken to the
non-linear editor.
Attaching the essence marks to the recorded data of this
unit
When you use the Content Browser Mobile application V2.0 or
later, you can attach the essence marks while recording to this
unit. They are also applied to the proxy data. You can set the clip
position of a file simply using this essence mark information.
Notes
• This is only enabled for the same size proxy data which
succeeds the original file information recorded to this unit.
• When the original file is divided, the essence marks are not
applied to the proxy data.
About setting the streaming format and proxy format
When "Bit Rate" of the proxy format setting is set to "9Mbps" in
V1.2 (camcorder software), "Bit Rate" of the streaming setting
cannot be set to more than "6Mbps. " However, the setting can be
done in V2.0 (camcorder software). If you select the preset whose
"Bit Rate" is set to more than "6Mbps, " "Bit Rate" of the streaming is
not changed to "3Mbps" automatically.
About the monitoring of Content Browser Mobile
The monitoring video image may stop due to signal conditions
when used or mobile devices.
Changed format for monitoring
"640×360 (3Mbps)" for "Size" is deleted from the monitoring
format. If you use this setting, "Size" is set to "480×270 (1Mbps). "
Changing the wireless LAN channel
The wireless LAN channel setting is changed partially ("Channel"
in the NETWORK SET menu).
Power supply to the wireless microphone installed on the
multi-interface shoe
Originally, power to the multi-interface shoe could not be
supplied while the network function was used. Due to this
version up, the power to the multi-interface shoe can be supplied
when the camcorder is driven by the battery. Therefore, you can
use the wireless microphone UWP-D11/D12 when the network
function is used.
Change of other menus
<LCD/VF SET menu>
• "NW Client Status" is added to "Display On/Off. "
The status display of the connection to the CCM turns on /off in
"NW Client Mode".
<NETWORK SET menu>
• Adding "6Mbps" in "Proxy File" > "Bit Rate"
• The menu name "Wi-Fi Remote" is changed to "Network
Remote. "
In changing the menu name, when "Wired LAN" is set in
"Network Mode" of the NETWORK SET menu, access to the Web
menu of the unit and Wi-Fi remote commander can be
performed.