Charging The Battery; Recommandations Importantes; Replacing The Battery - Peg-Perego Corral BEARCAT Empleo Y Manutencion

ASSEMBLY INSTRUCTIONS
WARNING
THE VEHICLE MUST BE ASSEMBLED BY ADULTS.
BEWARE WHEN EXTRACTING THE VEHICLE
FROM THE PACKAGING.
ALL THE NECESSARY SCREWS AND SMALL
COMPONENTS ARE STORED IN A BAG INSIDE
THE PACKAGING.
THE BATTERY MAY ALREADY BE INSTALLED.
Do not use the toy if you find it damaged after
opening the packaging. Contact the shop where you
bought it or the customer support centre.
Take care in the presence of children while
assembling the toy, given the risks caused by small
parts (ingestion hazard) and the plastic bags that
contain them (choking hazard).
To assemble the toy, you will need a flat-head
screwdriver, a Phillips screwdriver, a hammer, and a
pair of pliers.
ASSEMBLY
1 • FITTING THE FRONT WHEELS: Prepare 2 of
the 4 wheels, inserting a hexagonal bushing on
the inner side of each wheel. From the opposite
side, press a rim into place for each wheel.
2 • Remove the steering lever protection caps.
3 • Insert the following elements in sequence into a
steering lever: one large metal washer, one
wheel, one plastic washer, and one small metal
washer.
4 • Insert a nut and secure the wheel using the tool
supplied. Proceed in the same way for the other
front wheel.
5 • FITTING THE REAR WHEELS: Press the 2 round
elements (drivers) into place in the wheels, as
shown in the figure, and press the rims in place
into the outer part of the wheels.
6 • Remove the protection caps from the rear axle.
Insert the round bushing from the left-hand side
of the vehicle, leaving the smooth part facing
outwards. Insert the axle and a large metal
washer.
7 • Fit the wheel into the gearmotor on the right-
hand side of the vehicle. Insert the other wheel
on the opposite side. Insert a plastic washer and
a small metal washer on each side. Place the
respective nuts and secure the wheels
simultaneously using the tool supplied and pliers.
8 • Press the 4 hubcaps into place.
9 • Insert the gear shift lever into its housing, until it
snaps into place.
10 • Place the bumper at the front of the vehicle,
inserting the tab into its housing.
11 • Fasten the bumper.
12 • Insert the handlebar in its holder, taking care that
the grooves on the handlebar fit perfectly into
the slots, as shown in the figure.
13 • Tighten the assembled handlebar unit.
14 • Insert the handlebar cap.
15 • Insert the grips until reaching the end stop,
taking care that the notches engage properly.
16 • Insert the handlebar unit into the steering
column, pulling it upwards to ensure that the 2
holes correspond, as shown in the figure.
17 • Tighten.
18 • Insert the mudguard flap, taking care that the 2
hooks are fully engaged.
19 • Insert the screw into the hole and tighten the
flap. Proceed the same way for the other flap.
20 • Insert the antenna into its opening and push in
place.
21 • Rotate the red lock behind the saddle and bring
it to the position shown in the figure. A: the
saddle is locked; B: the saddle can be opened.
22 • Press the rear part of the bodywork down, to
facilitate the opening of the saddle. Lift the
saddle.
23 • Connect the plugs. Always remember to close
and to fasten the saddle when you have finished.
The vehicle is ready for use.
FEATURES AND USE OF THE VEHICLE
24 • PEDAL: Electric accelerator/brake pedal. The
brake activates automatically by lifting the foot.
25 • GEAR SHIFT LEVER: the vehicle has one forward
and one reverse gear.
I = first gear
R = reverse

REPLACING THE BATTERY

PLEASE NOTE: THE PICTURES OF THE BATTERIES
ARE FOR ILLUSTRATIVE PURPOSES ONLY. YOUR
BATTERY MAY BE DIFFERENT FROM THE MODEL
SHOWN. THIS DOES NOT AFFECT THE
REPLACEMENT AND CHARGING PROCEDURES
DESCRIBED.
26 • Rotate the red lock behind the saddle and open
it. Press the rear part of the bodywork down, to
facilitate the opening of the saddle. Lift the
saddle. Disconnect the wiring unit plug from the
battery plug by pressing on the sides.
27 • Loosen the battery holder and remove it.
28 • Replace the battery. Tighten the battery holder
back in place, reconnect plugs A and B, and close
the saddle.

CHARGING THE BATTERY

WARNING: BATTERY CHARGING AND ANY
OTHER WORK ON THE ELECTRICAL SYSTEM
MUST BE CARRIED OUT BY ADULTS.
THE BATTERY CAN ALSO BE CHARGED
WITHOUT REMOVING IT FROM THE TOY.
29 • Open the saddle. Disconnect the wiring unit
plug A from battery plug B, pressing on the
sides.
30 • Insert the battery charger plug into a domestic
power socket following the instructions
attached. Connect plug B with the battery
charger plug C.
31 • Once the battery is charged, remove the battery
charger from the domestic socket, then
disconnect plug C from plug B.
32 • Insert plug B into plug A until it clicks into
position. After completing the procedure, always
remember to reinstall the battery holder and
close and secure the saddle.
FRANÇAIS
PEG PEREGO ® vous remercie d'avoir
choisi ce produit. Depuis plus de 60 ans,
PEG PEREGO accompagne les promenades
des enfants. Dès leur naissance, avec les
landaus puis avec les poussettes et plus
tard, avec les jouets à pédales et à
batterie.
Découvrez sur notre site la gamme
complète des produits, les nouveautés et
d'autres renseignements sur le monde Peg
Perego.
www.pegperego.com
Peg Perego S.p.A. est une entreprise disposant
d'un système de management de la qualité certifié
conforme à la norme ISO 9001 par TÜV Italia
Srl. Cette certification garantit aux clients et aux
consommateurs une transparence et une confiance
en l'entreprise et son mode de fonctionnement.
RECOMMANDATIONS
IMPORTANTES
Lisez attentivement ce manuel d'instructions pour
vous familiariser avec le modèle et apprendre à votre
enfant à le conduire de façon correcte, amusante et
en toute sécurité. Conserver ensuite ce manuel pour
pouvoir vous y référer à l'avenir.
Si le produit est confié à des tiers, assurez-vous qu'il
soit accompagné du manuel d'instructions.
Avant d'utiliser le véhicule pour la première fois,
mettez en charge la batterie pendant 18 heures.
Ne pas appliquer cette règle pourrait être à l'origine
de dommages irréversibles à la batterie.
• Âge 2+
• Poids maximal autorisé 25 kg
• Véhicule à 1 place
• 1 Batterie rechargeable de 6 V 4,5 Ah scellée au plomb
• 1 roue motrice
• 1 moteur de 50 W
• Vitesse en première 3,7 km/h
• Vitesse en marche arrière 3,6 km/h
Ne pas dépasser le poids maximal autorisé de 25 kg.
Cette limite s'applique aussi bien aux conducteurs
qu'à l'éventuel chargement.
Peg Perego se réserve le droit d'apporter, à tout
moment, des modifications aux modèles et aux
données figurant dans ce livret, pour des raisons de
caractère technique ou de management.