Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
To reduce the risk of injury, wear safety goggles
or glasses with side shields. Unplug the tool
before changing accessories or making adjust-
m e n t s .
Starting and Stopping the Motor
Plug in the tool. To start the tool, squeeze the paddle trigger. Release the
paddle trigger to stop tool.
1.
To start the tool, squeeze the paddle trigger.
2.
To stop the tool, release the paddle trigger.
Sanding Disc and Grinding Wheel Selection
Use sanding discs and grinding wheels that are:
•
correct size as written on tool's nameplate.
•
correct wheel type and grit for the job.
•
rated at or above the RPM listed in the "WARNING" section on
the tool's nameplate.
Use backing pads, adapters, and other accessories that are:
•
correct size for tool and for sanding disc or grinding wheel.
•
rated at or above the RPM listed in the "WARNING" section on
the tool's nameplate.
•
the proper accessory for the job.
To reduce the risk of personal injury and
damage to the tool, use ONLY accessories
rated at or above the RPM listed on the
"WARNING" section of the tool's nameplate.
Sanding Disc and Grinding Wheel Material
Sanding discs and grinding wheels are made of various materials and
are designed for different jobs. Be sure that you choose the proper
sanding disc or grinding wheel for the job you plan to do.
Selecting Sanding Discs & Grit
Refer to the table below to select the correct type of sanding disc for
your job. Generally, use 24 or 36 grit for heavy stock removal; 50, 60, or
80 grit for medium stock removal and 120 grit for finishing. Always begin
with a coarse grit, using successively finer grits to obtain the desired
finish. See Catalogor a complete list of MILWAUKEE sanding discs.
Aluminum
Aluminum
Zirconia Bi-Cut
Oxide
For fast cutting, gen-
Unique grit pattern is
eral purpose discs
arranged in clusters
for most metal jobs.
for faster stock re-
Best for cold-rolled
moval and cleaning.
steel, stainless steel
Ideal for removing
paint
or metals requiring
tough, fast cutting,
boats, etc. without
long lasting abra-
clogging.
sives.
WARNING!
WARNING!
Ceramic
Lasts up to 3 times
longer than aluminum
oxide discs. For
general metal work-
ing. Ideal for tough
from
cars,
jobs.
OPERATION
Installing Backing Pad and Sanding Discs (Fig. 1)
1.
Unplug tool and place it upside down on a level surface as shown.
Remove any accessories from spindle.
2.
Slip backing pad onto spindle with flat side away from gear case.
Place sanding disc on backing pad and secure assembly to spindle
with disc nut.
3.
To tighten, press the spindle lock button while turning disc nut clock-
wise.
4.
To remove backing pad and sanding disc, unplug tool and reverse
procedure.
Fig. 1
Sanding Disc
Backing Pad
Sanding (Fig. 2)
1.
Use a clamp, vise or other practical means to hold your work, free-
ing both hands to control your tool. Firmly grasp body of tool and
side handle before starting and while tool is in operation. Allow
sanding disc to come to full speed before beginning to sand.
2.
Hold Sander/Grinder at 5° to 15° angle as shown to ensure proper
sanding pressure and control. Too great an angle will result in too
much pressure and could cause excessive wear to the disc and
workpiece. Too small an angle will reduce control.
3.
Use long, sweeping, side to side strokes, advancing forward to
produce the desired finish.
Fig. 2
For best result use only this portion of disc
Disc Nut
Spindle
Gear Case
Hold at a 5° to 15° angle
page 5
Publicidad
Tabla de contenido
