Rupes LE71T Traducción De Manual De Instrucciones Original página 9

INFORMATOIN NOISE / MEAN ACCELERATION VALUE
The tools are suppressed in accordance for the prevention and elimination of radio
disturbances measured in accordance with standard: EN 60745
Sound pressure level / Sound power level
L PA L WA
dB(A)
LE71T 74 85
LE71TE 74 85
LS71T 74 85
LS71TE 74 85
LR71TE 74 85
DANGER
The indicate measurements refer to new power tools.
Daily usa causes the noise and vibration values to change.
Displayed emission values are comparative and are to be employed for
a provisional assessment of the operator's risk exposure during the work period.
Appropriate evaluation of work period must also include tool's idle and stop
periods. These emission values represent the tool's main applications.
If the tool is used for other applications, with other accessories, or if it does not
undergo regular maintenance, emission values can significantly increase
during operations.
Use hearing protection!
PARTS OF THE TOOL
1 - Technical data identification label
2 - ON/OFF switch
3 - Speed control (LE71TE-LS71TE-LR71TE)
4 - 29 mm Ø suction port
5 - Velcro pad holder:
5a - Rectangular (LE71T-LE71TE)
5b - Triangular (LS71T-LS71TE)
5c - Circular (LR71TE)
6 - Motor ventilation slots
7 - Pad fixing screws
8 - Conical filter:
8a - Filter holder
8b - Cartridge
STARTING UP
WARNING
Pay attention to the mains voltage! The mains voltage must
correspond to the voltage indicated on the technical data identification
place (1).
3 axis vibration level
a h
Uncertainty Uncertainty
2
m/s
3 3,00 1,50
3 3,00 1,50
3 3,00 1,50
3 3,00 1,50
3 3,00 1,50
DANGER
Before any intervention on the electrical tool take the plug out
from the socket
BEFORE STARTING THE TOOL
Before starting-up the tool, ensure that:
- the packaging is complete and does not show signs of having been damaged
during storage or transport;
- the tool is complete; check that the number and type of components comply
with that reported in this instruction booklet;
- the power supply and socket outlet can support the load reported in the table
and that indicated on the tool identification plate reproduced;
- the power supply cable and plug are in perfect condition;
- the ON/OFF (2) switch works properly though with the power supply
disconnected;
- all the parts of the tool have been assembled in the proper manner and that
there are no signs of damage;
- the ventilation slots (6) are not obstructed;
- the tool must be connected to a suitable and efficient aspiration device.
ASSEMBLY/REPLACEMENT OF THE ABRASIVE PAPER
ASSEMBLY:
Press the abrasive paper into the pad (10) ensuring that the holes in the paper
coincide with extraction holes in the pad.
DISASSEMBLY:
- Used abrasive paper can be removed by simply tearing them off;
- new velcro abrasive paper it's mounted (see "ASSEMBLY")
SANDING PAD REPLACEMENT
Replace damaged sanding pad immediately. Optimal results are
achieved only using original accessories.The assembly of a sanding
pad with incorrect dimensions can cause excessive vibrations which
are not allowed for the machine.
- Unscrew the screws (7) on the pad;
- reverse the procedure when fitting the pad.
Start the tool and check that there are no unusual vibration, no dismatching
movement of the abrasive disc. Otherwise switch-off the tool immediately and
eliminate the cause.
STARTING AND STOPPING
- Starting: press the switch (2) down in position "ON".
- Stopping: press the switch (2) up in position "OFF".
WARNING: after an interruption of the electrical energy, if the
ON/OFF switch is inserted, it is necessary to release the switch (see
Stopped).
9