Spraying Precautions - Campbell Hausfeld CE2002 Serie Manual De Instrucciones Y Lista De Piezas

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Important Safety Information (Continued)
Check all fasteners at frequent intervals for proper tightness�
Never operate compressor without
a beltguard. This unit can start
automatically without warning. Personal injury or
property damage could occur from contact with moving
parts.
Do not wear loose clothing or jewelry that will get caught in
the moving parts of the unit�
Compressor parts may be hot even if
the unit is stopped.
Keep fingers away from a running compressor;
fast moving and hot parts will cause injury and/or
burns�
If the equipment should start to vibrate abnormally, STOP
the engine/motor and check immediately for the cause�
Vibration is generally an indication of trouble�
To reduce fire hazard, keep engine/motor exterior free of oil,
solvent, or excessive grease�
An ASME code safety relief valve with a setting
no higher than the Maximum Allowable
Working Pressure (MAWP) of the tank MUST be installed in the air
lines or in the tank for this compressor. The ASME safety valve must
have sufficient flow and pressure ratings to protect the pressurized
components from bursting. The flow rating can be found in the parts
manual. The safety valve in the intercooler does not provide system
protection.
Maximum operating pressure is 150 psi . Do not
operate with pressure switch or pilot valves set
higher than 150 psi.
Never attempt to adjust ASME safety valve� Keep safety valve
free from paint and other accumulations�
Never attempt to repair or modify
a tank! Welding, drilling or any
other modification will weaken the tank resulting in
damage from rupture or explosion. Always replace worn,
cracked or damaged tanks.
Drain liquid from tank daily.
Tanks rust from moisture build-up, which weakens the tank�
Make sure to drain tank regularly and inspect periodically for
unsafe conditions such as rust formation and corrosion�
Fast moving air will stir up dust and debris which may be
harmful� Release air slowly when draining moisture or
depressurizing the compressor system�
Check fuel level before starting the engine� Do not fill the
gas tank indoors� Wipe off any spilled gas before starting the
engine�
NEVER refuel a running or hot engine. Explosive
fuel can cause fires and severe burns. Avoid
overfilling fuel tank.
Gasoline vapor is highly flammable. Refill
outdoors or only in well ventilated areas. Do
not store, spill or use gasoline near an open flame or heat devices such
as a stove, furnace, or water heater, which utilize a pilot light, or any
device that can create a spark. If gasoline is accidentally spilled, move
unit away from the spill area and avoid creating any source of ignition
until gasoline vapors have dissipated.
Carbon monoxide can cause severe nausea,
fainting or death. Do not operate unit inside a
closed building or a poorly ventilated area.
Never remove or attempt to adjust safety valve.
Keep safety valve free from paint and other
accumulations.
Do not tamper with governor setting on engine�
Overspeeding the unit severely shortens engine life and may
also be very hazardous�

SpRAyinG pRecAutionS

Do not spray flammable materials
in vicinity of open flame or near
ignition sources including the compressor unit.
Do not smoke when spraying paint, insecticides,
or other flammable substances�
Use a face mask/respirator when spraying and
spray in a well ventilated area to prevent health
and fire hazards�
Do not direct paint or other sprayed material
at the compressor� Locate compressor as far away from
the spraying area as possible to minimize overspray
accumulation on the compressor�
When spraying or cleaning with solvents or toxic
chemicals, follow the instructions provided by the chemical
manufacturer�
SAve theSe inStRuctionS
do not diScARd
The DANGER, WARNING, CAUTION, and NOTICE
notifications and instructions in this manual cannot
cover all possible conditions and situations that may
occur� It must be understood by the operator that
caution is a factor which cannot be built into this
product, but must be supplied by the operator�
Series CE2002
www.campbellhausfeld.com
3

Publicidad

Tabla de contenido
loading

Tabla de contenido