Technical Data; Auxiliary Handle (See Figure A); Changing The Tool - Bosch GSB Professional 10 Manual Original

(11) Auxiliary handle (insulated gripping surface)
A)
(12) Depth stop
(13) Handle (insulated gripping surface)
A)
(14) Chuck key
A)
(15) Keyed chuck
A)
(16) Universal bit holder

Technical Data

Impact drill
Article number
Rated power input
Power output
No-load speed
Max. speed under load
Impact rate
Rated torque
Speed preselection
Right/left rotation
Spindle collar diameter
Max. drilling diameter
– Concrete
– Steel
– Wood
Chucking capacity
Weight according to EPTA-Pro-
cedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
Assembly
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Auxiliary Handle (see figure A) (GSB 13/
GSB 13 RE/GSB 16/GSB 16 RE)
Do not operate your power tool without the auxiliary
u
handle (11).
Before any work, make sure that the wing bolt is
u
tightened. Loss of control can cause personal injury.
You can swivel the auxiliary handle (11) to any angle for a
safe work posture that minimises fatigue.
Turn the wing bolt for adjusting the auxiliary handle anti-
clockwise and swivel the auxiliary handle (11) into the re-
quired position. Then retighten the wing bolt by turning it
clockwise.
Bosch Power Tools
A)
(17) Screwdriver bit
(18) Hex key
(19) Open-ended spanner
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
B) Commercially available (not included in the scope of deliv-
ery)
GSB ... 10 10 RE
3 601 ... B16 0.. B16 1..
W 500 500
W 250 250
-1
min 2600 0–2600
-1
min 1610 1610
-1
min 25700 25700
Nm 1.5 1.5
–
–
mm 43 43
mm 10 10
mm 8
mm 20 20
mm 1.5–10 1.5–10
kg 1.5 1.5
/ II / II
Setting the Drilling Depth (see figure A)
You can use the depth stop (12) to set the required drilling
depth X.
Press the button for depth stop adjustment (9) and insert
the depth stop into the auxiliary handle .
Pull the depth stop far enough out that the distance between
the drill bit tip and the edge of the depth stop corresponds
to the required drilling depth X.

Changing the Tool

Keyless Chuck (see figure B)
Hold the rear sleeve (3) of the keyless chuck (1) firmly and
turn the front sleeve (2) in the rotational direction ➊ until
the tool can be inserted. Insert the tool.
Hold the rear sleeve (3) of the keyless chuck (1) and firmly
tighten the front sleeve (2) by hand in the rotational direc-
tion ➋ until it stops clicking. This will automatically lock the
drill chuck.
A)B)
A)B)
A)B)
13 13 RE
B17 0.. B17 1..
B17 6..
600 600
301 301
2800 0–2800
1570 1570
25070 25070
1.8 1.8
– – –
● – ●
43 43
13 13
8 10 10
25 25
1.5–13 1.5–13 1.5–13
1.8 1.8
/ II / II
1 609 92A 4H4 | (21.09.2018)
English | 7
16 16 RE
B18 0.. B18 1..
B18 6..
701 701
351 351
3000 0–3000
1640 1640
26720 26720
2.0 2.0
– ●
– ●
43 43
16 16
12 12
30 30
1.5–13
1.9 1.9
/ II / II