Count.in./.Metronome; Count In Settings; Various.settings.(Utility); Checking The Lucina Ax-09'S Version - Roland Lucina AX-09 Manual De Usuario

Count In / Metronome
"Count in" refers to a feature that counts you in to the
beginning of the performance. To have a two-measure
count in be sounded, press the modulation bar while you
press the [PREVIEW] button.
Note that, if you wish, you can have a metronome be
sounded instead—simply change the Count Mode to
(METRONOME) using the setting below. The metronome
will continue to sound until you press the [PREVIEW]
button a second time.
* A.count.in.will.not.be.sounded.when.the.[AUDIO.
PLAYER].button.is.lighted ..

Count In Settings

1. Hold.down.the.[SHIFT].button.and.press.the.
[PREVIEW].button;.the.current.count.in.setting.will.
blink.in.the.display .
2. Continue.holding.down.the.[SHIFT].button,.and.
press.the.[PREVIEW].button.once.again.to.switch.
parameters .
After a brief interval, the value will appear; continue
holding down the [SHIFT] button, and use the [INC/+] /
[DEC/–] (OCTAVE [+] / [–]) buttons to edit the value.
Various Settings (Utility)
Checking the Lucina AX-09's
Version
Here's how to check the Lucina AX-09's version.
1. While.holding.down.the.FAVORITE.[A],.[B],.and.
[WRITE].buttons.simultaneously,.turn.on.the.
Lucina.AX-09's.power .
The display will indicate "
Utility mode.
2. Press.the.TONE.[1].button .
The display will indicate the version of your Lucina AX-09.
If you want to continue playing the Lucina AX-09, turn off
the power and wait several seconds before turning it on
again.

USB Driver Settings

When using a USB cable to connect the
Lucina AX-09 to your computer, you can
choose whether to use the standard USB
driver that's provided by your computer
or the USB driver provided by Roland.
18
Ut L
"; the Lucina AX-09 will be in
Parameter Value
o F F
C n t C i n
N t r
N t r
b P N
20–250
b A t
0.4, 2.4, 3.4, 4.4, 5.4, 6.4, 7.4
L u L
0–10
1 (Electronic metronome)
2 (Mechanical metronome)
3 (Pulse)
t y P
4 (Beep)
5 (Cowbell)
6 (Stick)
3. To.save.this.setting,.hold.down.the.[SHIFT].button.
and.press.the.[WRITE].button .
MEMO
To have the tempo of the count be shown in the
display, hold down the [PREVIEW] button. While in this
state, you can set a new tempo by tapping the [SHIFT]
button at least four times at the desired tempo; or you
can set it using the [INC/+] and [DEC/-] buttons.
MEMO
For details on connecting the Lucina AX-09 to your
computer via USB, refer to "Connecting to Your
Computer via USB" (p. 21).
1. While.holding.down.the.FAVORITE.[A],.[B],.and.
[WRITE].buttons.simultaneously,.turn.on.the.
Lucina.AX-09's.power .
The display will indicate "
Utility mode.
2. Press.the.TONE.[2].button .
The display will indicate "
shown and the [WRITE] button will blink.
3. Use.the.[INC/+]./.[DEC/–].buttons.to.choose.the.
desired.setting .
Value
G E n
.(GENERIC)
(Default)
u n D
.(VENDOR)
4. Press.the.[WRITE].button.to.save.the.setting .
5. Turn.the.Lucina.AX-09's.power.off,.then.on.again .
Now you'll be able to use the USB driver you choose.
Explanation
(OFF),
Count mode
(COUNT IN), Determines whether count in
or metronome will sound
(METRONOME)
Tempo of count
Time signature of count
(2.4 indicates 2/4 time)
Volume of count
Sound used for count
U tL
"; the Lucina AX-09 will be in
d ru
"; then the current value is
Explanation
Choose this if you're using the standard USB driver
provided by your computer.
Normally you'll use this mode.
Choose this if you're using the USB driver
downloaded from the Roland website.